Technical Analysts Jobs in Iraq
740 Jobs Found
Save and set alert for similar positionsManage alerts
<p>Job Responsibilities</p><p> </p><p>1. Reservoir Performance Analysis and Monitoring</p><p>• Monitor the production performance of oil wells and reservoirs; prepare periodic reservoir performance analysis reports.</p><p>• Analyze the effectiveness of water injection; optimize water injection schemes, adjust zonal injection structures, and maintain injection-production balance.</p><p>• Evaluate the production capacity of individual wells; identify low-producing, water-producing, or anomalous wells in a timely manner and provide evidence-based recommendations for well interventions or workovers.</p><p> </p><p>2. Numerical Simulation and Development Planning</p><p>• Build and maintain geological and numerical reservoir simulation models (using software such as Eclipse, tNavigator, or Petrel).</p><p>• Conduct history matching and forecast production trends under various development strategies.</p><p>• Prepare Oilfield Development Plans (ODP), design supplementary development adjustments, and draft proposals for new well construction.</p><p> </p><p>3. Testing and Data Acquisition Design</p><p>• Design and review programs for well testing, trial production, pressure monitoring (PBU/RFT/MDT), and fluid property (PVT) analysis.</p><p>• Interpret and evaluate well test data to derive key parameters such as formation pressure, permeability, and skin factor.</p><p> </p><p>4. Reserves and Asset Management</p><p>• Evaluate, calculate, and report remaining oilfield reserves in accordance with international standards (e.g., SPE-PRMS).</p><p>• Conduct in-depth research on the distribution of remaining oil to identify potential recovery opportunities within the field, including both peripheral and internal areas.</p><p> </p><p>5. Cross-functional Collaboration and Communication</p><p>• Collaborate closely with geology, drilling, production/completion, and surface facilities teams to ensure the successful implementation of development plans.</p><p>• Present technical proposals for review and approval.</p><p> </p><p>Qualifications</p><p>1. Education and Work Experience</p><p>• Bachelor’s degree or higher in Petroleum Engineering, Oil and Gas Field Development Engineering, or a related discipline.</p><p>• At least 8 years of experience in reservoir engineering within an oil company or oilfield service company (experience with carbonate, heavy oil, or low-permeability reservoirs is preferred). • Prior work experience on projects in the Middle East, or familiarity with oil fields in Iraq (such as Rumaila, West Qurna, Halfaya, Majnoon, etc.), is preferred.</p><p> </p><p>2. Professional Skills</p><p>• Proficient in core reservoir engineering software, including Eclipse, tNavigator, Petrel RE, Kappa (Saphir/Topaze), Prosper/GAP, OFM, etc.</p><p>• Possess a solid foundation in material balance, production decline analysis, and well test interpretation.</p><p>• Familiar with international reserve evaluation standards (PRMS).</p><p> </p><p>3. Language and Soft Skills</p><p>• Capable of using English as a working language, with the ability to fluently draft technical reports and deliver oral presentations in English (proficiency in Arabic is an advantage).</p><p>• Strong cross-cultural communication skills, resilience under pressure, and a collaborative team spirit.</p><p> </p><p>4. Adaptability to Work Environment</p><p>• Able to adapt to a rotational work schedule at field sites in Iraq.</p><p>• In good physical health and capable of adapting to the hot climate of the Middle East and the specific security/camp environment.</p>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>Wood is currently recruiting for an <strong>Instrument Advisor</strong> to join its Iraq business unit focusing on delivering and driving national technician coaching, mentoring, assessment & development in instrumentation and control. <br> This is a full-time onsite position in Basra, Iraq.</p><br><br> Wood is a global leader in consulting, engineering and operations for the energy and materials sectors. With 33,000 people in around 50 countries, Wood supports clients across the full asset lifecycle, delivering safe, predictable outcomes while enabling resilient operations and a lower carbon future. Wood forms the Energy & Materials pillar of Sidara - a global partnership uniting leading multidisciplinary engineering, design, and project management companies. www.woodgroup.com<br> <b>Diversity Statement </b><br> We are an equal opportunity employer that recognises the value of a diverse workforce. All suitably qualified applicants will receive consideration for employment on the basis of objective criteria and without regard to the following (which is a non-exhaustive list): race, colour, age, religion, gender, national origin, disability, sexual orientation, gender identity, protected veteran status, or other characteristics in accordance with the relevant governing laws.<br> </div>
<p><h4>Electrical technician</h4>
<p>Responsible for study, design, specification and services related to electrical and electronic systems including power generation, transmission and distribution, power systems performance and control, cabling and wiring, lighting, motor control centers, communications systems, cathodic protection, grounding lightning protection, heat tracing, etc.</p>
<p>Under direct supervision, evaluates, selects, and applies standard engineering techniques, procedures, and criteria, using judgment in making minor adaptations and modifications. With additional experience within one functional area, assists in the design of larger and more complex assignments which involve conventional types of plans, investigations and surveys with relatively few complex features for which there are precedents.</p>
<p>Job tasks, correctly performed, impact indirectly on cost containment, efficiency, profitability or operations. Skills are typically acquired through an undergraduate degree in engineering and minimum of 2 years related experience, with typical experience ranging from 3-7 years.</p>
<p>Assignments are generally well defined with clearly specified objectives. Assignments usually include one or more of the following:</p>
<ul>
<li>Design and development</li>
<li>Testing of materials</li>
<li>Preparation or checking of design calculations and specifications</li>
<li>Studies</li>
<li>Research investigations</li>
<li>Report preparation</li>
<li>Other activities of limited scope</li>
</ul>
<p>Certification as an engineer-in-training is preferred.</p></p><p></p>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p><b>Title:</b></p><br><br>Electrical Technician<br><br><p>Responsible for study, design, specification and services related to electrical and electronic systems including power generation, transmission and distribution, power systems performance and control, cabling and wiring, lighting, motor control centers, communications systems, cathodic protection, grounding lightning protection, heat tracing etc. Under direct supervision, evaluates, selects, and applies standard engineering techniques, procedures, and criteria, using judgment in making minor adaptations and modifications. With additional experience within one functional area, assists in the design of larger and more complex assignments which involve conventional types of plans, investigations and surveys with relatively few complex features for which there are precedents. Job tasks, correctly performed, impact indirectly on cost containment, efficiency, profitability or operations. Skills are typically acquired through an undergraduate degree in Engineering and minimum of 2 years related experience, with typical experience ranging from 3-7 years. Assignments are generally well defined with clearly specified objectives. Assignments usually include one or more of the following: design and development, testing of materials, preparation or checking of design calculations and specifications, studies, research investigations, report preparation, and other activities of limited scope. Certification as an Engineer-In-Training is preferred.</p><br><br><br><br><br> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>INTECH Process Automation is seeking a Seasoned<strong> Commissioning Technician (Electrical) </strong>to join our Operations & Maintenance (O&M) team. The selected candidate will be responsible for <strong>electrical pre-commissioning, testing, inspection, rectification, and documentation</strong> under approved procedures and Engineer supervision. Ensure electrical systems supporting instrumentation and ICSS are safely tested and ready for energization and handover.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform assigned <strong>electrical pre-commissioning and commissioning tests</strong> under Engineer supervision.</li><li>Conduct <strong>continuity, insulation resistance (IR), earth/grounding, polarity, and functional tests</strong>.</li><li>Inspect and verify <strong>cables, terminations, glands, panels, connections, and labeling</strong>.</li><li>Perform checks on <strong>UPS, battery systems, control power supplies, and distribution panels</strong>.</li><li>Support testing of electrical power supplies serving <strong>Instrumentation, ICSS, DCS, SIS, PLC, and F&G systems</strong>.</li><li>Identify and rectify approved <strong>electrical defects and punch-list items</strong>.</li><li>Support <strong>LOTO, isolation, de-energization, energization, and safe reinstatement</strong> activities.</li><li>Maintain <strong>test equipment, meters, tools, cables, and commissioning consumables</strong>.</li><li>Complete <strong>test sheets, checklists, punch records, inspection records, and commissioning documentation</strong>.</li><li>Report failed tests, defects, abnormal conditions, and unresolved issues to the <strong>Commissioning Engineer</strong>.</li><li>Coordinate with <strong>Electrical, Instrumentation, ICSS, Operations, Construction, HSE, and vendors</strong>.</li><li>Comply with <strong>PTW, LOTO, electrical safety, HSE, quality, and Company requirements</strong>.</li></ul> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>INTECH Process Automation is seeking a Seasoned<strong> Commissioning Technician (Instrument) </strong>to join our Operations & Maintenance (O&M) team. The selected candidate will be Responsible for <strong>instrument pre-commissioning, commissioning, calibration, loop checking, functional testing, and punch-list rectification</strong> in accordance with approved procedures. Ensure accurate test results, proper defect reporting, and safe system readiness for handover.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform <strong>instrument pre-commissioning and commissioning</strong> activities in accordance with approved procedures.</li><li>Conduct <strong>calibration, continuity checks, loop checks, and signal verification</strong>.</li><li>Configure and test <strong>field instruments, smart devices, and instrument interfaces</strong>.</li><li>Perform <strong>functional, Cause & Effect, alarm, interlock, and shutdown tests</strong> under Engineer supervision.</li><li>Verify instrument signals and functionality through <strong>DCS, SIS/ESD, F&G, PLC, and ICSS interfaces</strong>.</li><li>Identify, troubleshoot, and rectify <strong>commissioning defects and punch-list items</strong>.</li><li>Support <strong>energization, isolation, reinstatement, startup, and controlled return to service</strong>.</li><li>Maintain and verify <strong>test equipment, calibration standards, tools, and commissioning consumables</strong>.</li><li>Complete <strong>test sheets, calibration records, checklists, punch lists, and commissioning documentation</strong>.</li><li>Report abnormal conditions, failed tests, defects, and unresolved issues to the <strong>Commissioning Engineer</strong>.</li><li>Coordinate with <strong>Operations, Instrumentation, ICSS, Electrical, Mechanical, Construction, HSE, and vendors</strong>.</li><li>Comply with <strong>PTW, LOTO, HSE, process safety, quality, and commissioning requirements</strong>.</li></ul> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p><b>Tiered Approach</b></p><br> <p>In line with the commitment to safeguard capacity and support personnel already in the Organization, a majority of UNDP UNCDF/UNV vacancies are advertised using a tiered application process whereby:</p><br> <ul> <li><b>Tier 0</b>: UNDP/UNCDF/UNV IP staff holding permanent (PA) and fixed-term (FTA) appointments, whose posts will be abolished, or contracts will be terminated or not renewed during 2026.</li> <li><b>Tier 1</b>: Other UNDP/UNCDF/UNV staff holding permanent (PA) and fixed-term (FTA) appointments</li> <li><b>Tier 2</b>: UNDP/UNCDF/UNV staff holding temporary appointments (TA), personnel on regular PSA contracts, and Expert and Specialist UN Volunteers</li> <li><b>Tier 3 or no tier indicated</b>: All other contract types from UNDP/UNCDF/UNV and other agencies, and other external candidates</li> </ul> <p>Please make note of the Tier(s) indicated in the vacancy title, if any, and ensure that you satisfy the eligibility to apply.</p><br> <p><b>Office/Unit/Project Description </b></p><br> <p>The UNV Field Units (FU) are mainly accountable for the mobilization and placement of UN Volunteers in UN Agencies, Funds, and Programmes focused on peace, development and humanitarian needs. The UNV Field Units represent and position UNV in the respective countries and bring UNV’s services and solutions closer to its partners from governments, UN entities, civil society and private sector. </p><br> <p><b>Scope of Work </b></p><br> <p><b>1. Coordinate Country-level partnership development, demand analysis and volunteer mobilization </b></p><br> <ul> <li>Proactively develop and sustain partnerships at the country level with UN agencies, government institutions, civil society and partners to advance UNV’s mandate, identify collaboration opportunities, and ensure effective integration of volunteer solutions into programme delivery.</li> <li>Participate in UN collective planning processes (CCA, UNSDCF, humanitarian response plans, thematic task forces) to integrate volunteerism in their implementation.</li> <li>Analyze the United Nations Sustainable Development Cooperation Framework, Country Programme Documents, and sectoral strategies to identify priority entry points for integrating UNV volunteer solutions. </li> <li>Analyze partner demand and contribute to the development and execution of country-level volunteer mobilization strategies in line with UNV’s Strategic Framework.</li> <li>Identify and assess opportunities for the deployment of onsite and online Volunteers across development, humanitarian, and peace portfolios, in line with partner priorities. </li> <li>Promote volunteerism at the field level by organizing outreach activities, supporting awareness campaigns, and engaging partners and communities to integrate volunteer solutions into local development and humanitarian initiatives.</li> <li>Articulate and present UNV’s value proposition and volunteer modalities to partners through data‑driven briefing materials, presentations, and analytical notes.</li> <li>Support national talent attraction and pipeline management based on country demand forecasts and recruitment priorities, in coordination with the Regional Talent Acquisition Analyst.</li> </ul> <p><b>2. Ensure Business intelligence, demand analysis and planning</b></p><br> <ul> <li>Develop and maintain structured country‑level business intelligence on UN partner mandates, programme pipelines, and emerging priorities relevant to volunteer mobilization.</li> <li>Monitor mobilization trends, track key performance indicators, and use corporate tools (CRM, BI reports, UVP) to support planning, forecasting, and strategic decision making. </li> <li>Contribute to adapting regional volunteer mobilization priorities into country-specific recommendations, based on partner needs, data analysis, and local context. </li> <li>Contribute to the identification of thematic volunteer solutions, pilot initiatives, and joint approaches aligned with national needs and UN priorities in the country.</li> </ul> <p><b>3. Ensure Duty of Care</b></p><br> <ul> <li>Coordinate closely with the Field Security Officer and host entities to ensure that UN Volunteers are adequately informed of, and compliant with, all applicable security policies, procedures, and risk‑mitigation measures.</li> <li>Ensure timely and compliant medical evacuation support for UN Volunteers, ensuring coordination with medical providers, host entities, and relevant offices at UNV</li> <li>Ensure the well‑being and performance of serving UN Volunteers by maintaining regular contact, conducting periodic field visits to duty stations, and engaging with supervisors and counterparts to address emerging issues and support effective service delivery.</li> <li>In consultation with relevant sections, provide timely support to the UN Volunteers throughout their volunteer’s journey</li> </ul> <p><b>4. Ensure Management, knowledge building and sharing</b></p><br> <ul> <li>Develop and manage the implementation of the Field Unit’s annual work plan and set performance indicators, including management and reporting on UNV operational support funds and budget; </li> <li>Facilitate the effective functioning of the UNV country presence by ensuring coordinated service delivery and promoting a supportive and collaborative work environment that supports learning, professionalism. </li> <li>Manage any UNV assigned personnel within the FU including supervision, performance assessment and capacity development. </li> <li><b>Facilitate </b>knowledge and capacity building, knowledge sharing and advocacy</li> </ul> <p>The incumbent performs other duties within their functional profile as deemed necessary for the efficient functioning of the Office and the Organization</p><br> <p>Supervisory/Managerial Responsibilities: May supervise the Communications personnel in the Regional Office.</p><br> <p><b>Institutional Arrangement</b></p><br> <p>Reporting to the Portfolio Manager/Specialist, Regional Office, the Partnership Analyst leads country‑level analytical and partnership support to advance UNV’s volunteer mobilization agenda in the country. The position combines strategic partnership analysis, business intelligence, and operational coordination, while overseeing the team of UN Volunteers supporting Field Unit activities.</p><br> <p>The incumbent is responsible for strengthening UNV’s positioning as a solution provider for UN partners, supporting increased and diversified volunteer mobilization, and ensuring coherence between country‑level engagement and regional and global UNV priorities.</p><br> <p>As UNV is a systemwide service administered by UNDP, FUs are hosted within relevant UNDP offices, collaborating closely with the UNDP Resident Representative and the UN Resident Coordinator. The Partnership Analyst ensures compliance with UNV and UNDP policies, rules and regulations.</p><br> <p><b>Competencies</b></p><br> <b>CORE</b> <br> <p>Achieve Results </p><br> <ul> <li>Scale up solutions and simplifies processes, balances speed and accuracy in doing work</li> </ul> <p>Think Innovatively: </p><br> <ul> <li>Offer new ideas/open to new approaches, demonstrate systemic/integrated thinking </li> </ul> <p>Learn Continuously: </p><br> <ul> <li>Go outside comfort zone, learn from others and support their learning</li> </ul> <p>Adapt with Agility: </p><br> <ul> <li>Adapt processes/approaches to new situations, involve others in change process </li> </ul> <p>Act with Determination: </p><br> <ul> <li>Able to persevere and deal with multiple sources of pressure simultaneously</li> </ul> <p>Engage and Partner: </p><br> <ul> <li>Is facilitator/integrator, bring people together, build/maintain coalitions/partnerships</li> </ul> <p>Enable Diversity and Inclusion: </p><br> <ul> <li>Facilitate conversations to bridge differences, considers in decision making </li> </ul> <p><b>Cross-Functional & Technical competencies:</b></p><br> <p>System Thinking</p><br> <ul> <li>Ability to use objective problem analysis and judgement to understand how interrelated elements coexist within an overall process or system, and to consider how altering one element can impact on other parts of the system</li> </ul> <p>Negotiation and Influence: </p><br> <ul> <li>Reach a common understanding/agreement, persuade others, resolve points of difference through a dialogue, negotiate mutually acceptable solutions and create ‘win-win’ situations.</li> </ul> <p>Results-based Management </p><br> <ul> <li>Ability to manage the implementation of strategies, programmes, and projects with a focus at improved performance and demonstrable results. Knowledge and understanding of relevant theories, concepts, methodologies, instruments, and tools.</li> </ul> <p>Partnerships Management </p><br> <ul> <li>Build and maintain partnerships with wide networks of stakeholders, Governments, civil society and private sector partners, experts and others in line with UNDP strategy and policies</li> </ul> <p>Knowledge Generation </p><br> <ul> <li>Ability to research information and to turn it into useful knowledge, relevant for context, or responsive to a stated need. Ability to apply existing concepts to new situations, and to develop new concepts to generate workable solutions and new approaches. Knowledge of relevant concepts, conceptual models, and theories that can be useful in addressing new situations. </li> </ul> <p>Digital Awareness and Literacy </p><br> <ul> <li>Ability to monitor new and emerging technologies, as well as understand their usage, potential, limitations, impact, and added value. Ability to rapidly and readily adopt and use new technologies in professional activities, and to empower others to use them as needed. Knowledge of the usage of digital technologies and emerging trends. </li> </ul> <p>Event planning and execution </p><br> <ul> <li>Ability to plan, manage and execute of public and private events to ensure that they support and amplify individual communications and advocacy initiatives, as well as UNV's overall brand and mandate.</li> </ul> <p><b>Required Skills and Experience</b></p><br> <p><b>Education:</b></p><br> <ul> <li>Advanced university degree (master's degree or equivalent) in partnership, social sciences, international development, project management, public/business administration or related fields is required, or</li> <li>A first-level university degree (bachelor’s degree) in combination with two additional years of qualifying experience will be given due consideration in lieu of the advanced university degree.</li> </ul> <p><b>Experience:</b></p><br> <ul> <li>Minimum of 2 years (with master’s degree) or 4 years (with bachelor’s degree) in partnerships, development cooperation, international relations, research, programme analysis, preferably in a humanitarian, development and/or peace related field; </li> <li>Experience in partnerships, inter-agency collaboration, or stakeholder engagement is required.</li> <li>Experience conducting analytical work such as partner mapping, business intelligence, demand analysis, preparation of briefs, concept notes, or knowledge products.</li> <li>Strong drafting, analytical, and communication skills, with the ability to translate strategic priorities into clear, actionable inputs.</li> <li>Proficiency in the use of standard office software and digital collaboration tools.</li> <li>Openness to embrace Digital Transformation and use of new technologies.</li> <li>Experience working directly with the United Nations system, UNDP, UNV, or other international organizations is an asset</li> <li>Previous experience in volunteer management, promotion of volunteerism, or engagement with civil society organizations is a distinctive advantage.</li> <li>Experience supporting partnership development is a strong advantage.</li> </ul> <p><b>Languages:</b></p><br> <ul> <li>Fluency in English and Arabic</li> </ul> <p><b>Disclaimer:</b></p><br> <ul> <li>Only short-listed applicants will be contacted.</li> <li>The successful candidate will hold a UNDP IPSA contract.</li> <li>This vacancy announcement is open to Tier 0, 1 and 2 candidates.</li> </ul> <p><b>Equal opportunity</b></p><br> <p>As an equal opportunity employer, UNDP values diversity as an expression of the multiplicity of nations and cultures where we operate and, as such, we encourage qualified applicants from all backgrounds to apply for roles in the organization. Our employment decisions are based on merit and suitability for the role, without discrimination. </p><br> <p>UNDP is also committed to creating an inclusive workplace where all personnel are empowered to contribute to our mission, are valued, can thrive, and benefit from career opportunities that are open to all.</p><br> <p><b>Sexual harassment, exploitation, and abuse of authority</b></p><br> <p>UNDP does not tolerate harassment, sexual harassment, exploitation, discrimination and abuse of authority. All selected candidates, therefore, undergo relevant checks and are expected to adhere to the respective standards and principles. </p><br> <p><b>Right to select multiple candidates</b></p><br> <p>UNDP reserves the right to select one or more candidates from this vacancy announcement. We may also retain applications and consider candidates applying to this post for other similar positions with UNDP at the same grade level and with similar job description, experience and educational requirements.</p><br> <p><b>Scam alert</b></p><br> <p>UNDP does not charge a fee at any stage of its recruitment process. For further information, please see www.undp.org/scam-alert.</p><br> <p><b>Data Privacy</b></p><br> <p>Please click here to view UNDP Data Privacy Statement</p><br><br> #LI-DNI<br><br> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>Overview Working across the globe, V2X builds smart solutions designed to integrate physical and digital infrastructure from base to battlefield. We bring 120 years of successful mission support to improve security, streamline logistics, and enhance readiness. Aligned around a shared purpose, our $3.9B company and 16,000 people work alongside our clients, here and abroad, to tackle their most complex challenges with integrity, respect, responsibility, and professionalism. Responsibilities This posting is part of our ongoing talent pipeline and is not tied to an active opening; qualified candidates will be contacted when the role officially becomes available Summary: The F-16 Weapons Technician is responsible for the Oversight/Training/Instruction of inspections, maintenance, and repair of weapons systems and associated equipment on the F-16 aircraft , loading ordnance, and configuring load outs for each flight. Oversight/Training/Instructions for the following duties and responsibilities: + Administers/monitors weapons loading standardization training and evaluation programs. + Documents/ maintains qualification/certification status per the company training and certification requirements. + Weapons load crew duties, as required , in support of training exercises, inspections, etc. + Monitors flightline munitions/explosive handling and loading operations, if applicable. + Monitors load crews during operations + Maintains current awareness and training of proper weapons storage and security, if applicable. + Armament systems maintenance/loading/flight operations, as applicable. + Installation/removal of alternate mission equipment (AME) and normally-installed equipment, as needed, and weapons OPS checks. + One-time inspections (OTI); Time Compliance Tech Orders (TCTO); and maintains /inspects tools and equipment. + May be asked to perform End-of-Runway (EOR) inspections, if needed. + Troubleshooting and repairs to assigned aircraft as directed. + Read and interpret schematics, engineering drawings, and other technical directives. + Ensure the work accomplished on any aircraft or component is in compliance + Complete and certify work reports for all work accomplished on the aircraft . + Follow company procedures as per the maintenance operations manual using safe work practices. + Ability to work independently and to carry out assignments to completion within parameters of instructions given prescribed routines, and standard accepted practices. Qualifications Job Requirements: + High school diploma or GED required + Associate degree strongly preferred, Bachelor's Degree or equivalent a plus + A minimum of 8-10 years of direct F-16 Weapons/Armament Maintenance experience and training on F-16 aircraft . + USAF 7 – Level skill or equivalent What We Bring + At V2X, we strive to be market competitive in our total reward offerings. + The successful candidate’s starting pay will be based on, but not limited to, their job-related skills, experience, qualifications, work location, and market conditions. + Please speak with a recruiter for additional information. + Employee benefits include the following: + Healthcare coverage + Retirement plan + Life insurance, AD&D, and disability benefits + Wellness programs + Paid time off, including holidays + Learning and Development resources + Employee assistance resources + Pay and benefits are subject to change at any time and may be modified at the discretion of the company, consistent with the terms of any applicable compensation or benefit plans. At V2X, we are deeply committed to both equal employment opportunity, including protection for Veterans and individuals with disabilities, and fostering an inclusive and diverse workplace. We ensure all individuals are treated with fairness, respect, and dignity, recognizing the strength that comes from a workforce rich in diverse experiences, perspectives, and skills. This commitment, aligned with our core Vision and Values of Integrity, Respect, and Responsibility, allows us to leverage differences, encourage innovation, and expand our success in the global marketplace, ultimately enabling us to best serve our clients</p> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>INTECH Process Automation is seeking a seasoned <strong>Tank Calibration Technician</strong> to join our Operations & Maintenance (O&M) team. The selected candidate will be responsible for performing and supporting <strong>tank gauging, calibration, measurement verification, and documentation</strong> activities in accordance with approved procedures and reference standards. Ensures accurate, traceable measurements and safe execution of calibration work in tank areas.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform or assist with <strong>tank gauging and calibration/verification</strong> activities using approved procedures.</li><li>Inspect and verify <strong>tank level, gauging, measurement, and associated instrumentation</strong>.</li><li>Use approved <strong>reference standards, calibration equipment, and measurement tools</strong>.</li><li>Perform required <strong>measurements, calculations, comparisons, and verification</strong> of tank readings.</li><li>Ensure calibration equipment and reference standards have valid <strong>calibration status and traceability</strong>.</li><li>Record <strong>as-found/as-left readings, measurements, calculations, deviations, and calibration results</strong>.</li><li>Identify and report <strong>measurement errors, abnormal readings, instrument defects, and discrepancies</strong>.</li><li>Support troubleshooting, adjustment, replacement, and verification of <strong>tank gauging instruments</strong>.</li><li>Maintain accurate <strong>calibration certificates, test sheets, inspection records, and CMMS documentation</strong>.</li><li>Coordinate with <strong>Instrumentation, Operations, Maintenance, QA/QC, ICSS, and approved calibration/service providers</strong>.</li><li>Maintain calibration equipment, tools, standards, and work areas in <strong>safe and serviceable condition</strong>.</li><li>Follow <strong>tank-entry restrictions, gas testing, PTW, LOTO, hazardous-area, HSE, and process safety requirements</strong>.</li><li>Ensure all measurements and records remain <strong>complete, accurate, traceable, and auditable</strong>.</li></ul> </div>
<p><br></p> <p> <br>At <strong>Eni</strong>, we are looking for a <strong>Junior Compliance Analyst</strong> to join <strong>Eni Iraq B.V.</strong> in <strong>Basra</strong>. You will be responsible for supporting the Governance & Compliance Manager with Internal Control over Financial Reporting (ICFR) requirements, including the Sarbanes-Oxley Act (SOX), FRA and ELC/PLC, as well as maintaining Eni Iraq s Regulatory System in line with HQ requirements.</p> <p> <strong>Main responsibilities:</strong> </p> <ul> <li>Support the Governance & Compliance Manager in a timely and proactive manner.</li> <li>Assess and monitor Eni Iraq s Internal Control over Financial Reporting (ICFR/SOX) system, including complete, accurate and timely record-keeping.</li> <li>Support the reporting of outcomes from ICFR monitoring activities, including CELC/ERICE.</li> <li>Support the Governance & Compliance Manager during internal and external ICFR/SOX audits.</li> <li>Support self-assessments and monitor related action plans.</li> <li>Support the implementation and updating of Eni Iraq s Finance & Control Regulatory System, including the adoption of MSGs, procedures, OPIs and best practices.</li> <li>Track and monitor the timely implementation of action plans.</li> <li>Support the Governance & Compliance Manager with internal assessments, audits and projects, as required.</li> </ul> <p> <strong>Skills and experience required:</strong> </p> <ul> <li>Bachelor s degree in Accounting, Business Administration or a related discipline.</li> <li>Relevant experience within a Big Four firm, international company or similar role.</li> <li>Master s degree, ACCA, CPA or equivalent is preferred.</li> <li>Fluency in English and Arabic; Italian is an advantage.</li> <li>Strong analytical, communication and interpersonal skills.</li> <li>Good planning, organisational and problem-solving skills.</li> <li>Results-oriented, risk-aware and detail-focused.</li> <li>Ability to meet deadlines and work with minimal supervision.</li> <li>Good Microsoft Office skills.</li> <li>High level of integrity, responsibility and reliability.</li> </ul> <p><br></p><p><strong>Desired Candidate Profile</strong></p><p> <strong>Skills and experience required:</strong> </p> <ul> <li>Bachelor s degree in Accounting, Business Administration or a related discipline.</li> <li>Relevant experience within a Big Four firm, international company or similar role.</li> <li>Master s degree, ACCA, CPA or equivalent is preferred.</li> <li>Fluency in English and Arabic; Italian is an advantage.</li> <li>Strong analytical, communication and interpersonal skills.</li> <li>Good planning, organisational and problem-solving skills.</li> <li>Results-oriented, risk-aware and detail-focused.</li> <li>Ability to meet deadlines and work with minimal supervision.</li> <li>Good Microsoft Office skills.</li> <li>High level of integrity, responsibility and reliability.</li> </ul>
<p>Carry out different assignments of the financial and operational audits for the company and ensures the work is performed with the professional care and in accordance with the appropriate standards. These different activities involve conducting performance, operational, financial and compliance audits. Perform financial and operational audits in accordance with Asiacell internal audit methodology. Conduct interviews, review documents, audit surveys, compose summary memos, and prepare working papers. Assist in the preparation of the audit programs with appropriate testing mechanisms, execute the audit program, recognize control weaknesses, asses the materiality of these weaknesses, and relate them back to the scope and objective of the audit. Identify, develop, and document audit observations and recommendations for improvement. Assist in communicating the results, findings and recommendations of audit projects in a timely basis to management Follow up the implementation of the audit recommendations in a timely manner, as per the agreed-on follow-up programs. Interact with staff, section heads, and managers and when necessary, with department directors in order to obtain and/or communicate relevant information to achieve the objective/s of the financial & operational audits. Maintain all organizational and professional ethical standards and ensure internal audit activities are carried out in compliance with international standards for the professional practice of internal auditing, IIA code of ethics. Special assignments and investigations. Assists in the conduct of any fraud investigations or any special audit assignments as instructed by Sr. Manager. Assists in communicating the results, findings and recommendations of special assignments/investigations via written reports and presentations on a timely basis to the management Development & improvement program Pursue professional development opportunities, including external and internal training and professional association memberships, and shares information gained with co-workers. Proactively take responsibility for self-improvement by staying well-informed of developments, knowledge and innovations in relevant field of expertise.</p><p><strong>Desired Candidate Profile</strong></p><ul><li>Bachelor's degree in accounting or equivalent</li><li>Behavioral Competencies: Delivering Results & Fostering Ownership Building Customer Value Networking & Influencing Collaboratively Leading Teams Driving Change</li><li>Technical Competencies: Technical Writing and Reporting Critical Thinking Business English International Professional Practices Framework Internal Audit Planning & Execution Business Acumen Telecom Market & Industry Knowledge Digital Technology Knowledge</li></ul>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>INTECH Process Automation is seeking a Seasoned<strong> Piping/Tubing Technician </strong>to join our Operations & Maintenance (O&M) team. The selected candidate will be responsible for <strong>fabrication, installation, maintenance, testing, and repair of instrument tubing and small-bore piping systems</strong>. Ensure tubing and piping assemblies are correctly installed, leak-free, properly supported, clean, identified, and protected.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Fabricate and install <strong>instrument tubing and small-bore piping assemblies</strong> in accordance with approved drawings and procedures.</li><li>Perform accurate <strong>tube cutting, bending, routing, and preparation</strong>.</li><li>Install and tighten <strong>compression fittings, manifolds, valves, regulators, and tubing connections</strong>.</li><li>Install and maintain proper <strong>supports, clamps, brackets, and tubing protection</strong>.</li><li>Perform <strong>leak, pressure, and functional tests</strong> as required.</li><li>Inspect tubing and piping for <strong>correct routing, slope, supports, fittings, cleanliness, and workmanship</strong>.</li><li>Troubleshoot and repair <strong>leaks, damaged tubing, fittings, and small-bore piping defects</strong>.</li><li>Support installation and maintenance of <strong>impulse lines, pneumatic tubing, hydraulic tubing, and instrument connections</strong>.</li><li>Ensure tubing systems are properly <strong>identified, tagged, protected, and weatherproofed</strong>.</li><li>Maintain cleanliness and prevent <strong>contamination, moisture ingress, and blockage</strong> during fabrication and installation.</li><li>Restore and verify <strong>supports, clamps, insulation interfaces, and protective arrangements</strong> after maintenance.</li><li>Coordinate with <strong>Instrumentation, Piping, Mechanical, Operations, ICSS, Construction, and HSE</strong> teams.</li><li>Maintain <strong>test records, inspection results, material records, and work completion documentation</strong>.</li><li>Comply with <strong>PTW, LOTO, HSE, pressure safety, quality, and Company requirements</strong>.</li></ul> </div>
<p><h4>Job description</h4>
<p>The non-destruction inspection technician (NDI) II inspects aerospace weapon systems components and support equipment for structural integrity using nondestructive inspection methods and performs fluid analysis.</p>
<p>Determine test method and prepare fluids and parts for nondestructive inspection.<br>
Interpret nondestructive inspection test results and provide information about defects to repair center.<br>
Analyze wear metal content reports on engine lubricating oil and other fluids and recommend corrective action.<br>
Establish radiation areas for radiographic operations.<br>
Compute and monitor personal exposure areas for radiographic operations, and monitor personnel exposure data.<br>
Perform nondestructive inspection on structures, components, and systems.<br>
Detect flaws such as cracks, delaminations, voids, processing defects, and heat damage using penetrant testing, eddy current, magnetic particle, radiographic, optical, and ultrasonic test equipment.<br>
Determine metallurgical information of components according to alloy, temper, conductivity, and associated factors.<br>
Operate, maintain, and inspect nondestructive equipment.<br>
Perform operator maintenance and service inspections on shop equipment and tools.<br>
Ensure lock out and tag out procedures are accomplished prior to maintenance on equipment.<br>
Perform silver recovery functions.<br>
Handle and dispose of hazardous waste and materials.<br>
Perform other qualified duties as assigned.</p>
<h4>Minimum requirements</h4>
<p>High school diploma or equivalent required.<br>
U.S. military technical school or specialized training course is desired, certification of education level is required.<br>
Completion of an initial nondestructive inspection level II training course and current basic qualification.<br>
Three (3) or more years’ experience as an aviation inspector and a minimum of one year experience on the assigned (MDS) airframe (UH60, AH64, CH47).<br>
Shall be trained and qualified per NAS 410 or ASNT-CP-189 to the level assigned.<br>
Must be in possession of a U.S. passport with 3 years of validity remaining at the time of hire and be able to travel internationally.<br>
Ability to obtain and maintain a US government security clearance, NAC-I T1 public trust. US citizenship is required to obtain a T1/CAC NACI clearance.<br>
Able to clear CENTCOM medical requirements for deployment.<br>
Ability to obtain and maintain Iraq visa.</p>
<h4>Knowledge and skills</h4>
<ul>
<li>Previous experience in the maintenance, modification and repair of tactical aircraft systems of the type being serviced and their associated components (UH60, AH64, CH47).</li>
<li>Have the skills and knowledge to set up and standardize equipment, conduct tests, interpret and evaluate for acceptance or rejection, and document.</li>
<li>Thoroughly familiar with the scope and limitations of the technique/method in which they are certified.</li>
<li>Capable of providing the necessary guidance and supervision to trainers and Level I personnel in the technique/method in which they are certified.</li>
<li>Familiar with the codes, standards, and other contractual documents that control the method as utilized by the employer.</li>
<li>Capable of developing written instructions from approved general procedures. Such instructions shall require final approval by a Level III.</li>
<li>Knowledge of electrical, mechanical, electronic, hydraulic and pneumatic systems or other technology as applicable to fabrication, repair, operation and maintenance requirements.</li>
<li>Efficient in record keeping and preparation of reports; capable of reviewing other people's work and determining accuracy and conformity to standards.</li>
<li>Proficient in the use of the Unit Level Logistics System-Aviation Enhanced (ULLS-AE), the current maintenance management system utilized to maintain Army aircraft forms and records.</li>
<li>Comprehensive knowledge of aircraft mechanical component troubleshooting/repair procedures and replacement of components.</li>
<li>Thorough knowledge of aircraft sheet metal/structural modification and repair and the ability to determine functionality of non-complex electrical systems.</li>
<li>Detailed knowledge of aircraft unique tools such as test equipment, torque wrenches, dial indicators, micrometers, cable tensiometers, sheet metal brakes and shears, etc. is required.</li>
<li>Ability to provide technical support to structural/mechanical engineers and customers.</li>
<li>Excellent organizational skills in prioritizing workload to meet aircraft delivery schedule.</li>
</ul>
<h4>Physical requirements and working environment</h4>
<ul>
<li>Must be able to walk and stand on level and/or inclined surfaces for extended periods throughout the day.</li>
<li>Must be able to climb stairs, ramps, ladders, and work stands.</li>
<li>Must be able to crouch, crawl, grasp or handle objects, use finger dexterity, bend elbow/knee and reach above/below shoulders.</li>
<li>May be required to lift heavy objects whose weight may exceed 50 pounds.</li>
<li>Must be able to type using a standard keyboard to communicate through e-mail and various software applications.</li>
<li>Will handle dirty parts and lubricants.</li>
<li>Will be required to wear proper personal protective equipment (PPE).</li>
<li>Must be able to pass a respirator physical and fit test qualification.</li>
<li>May be required to operate power vehicles, machinery, hand tools, ground support equipment, forklift, etc.</li>
<li>Must be able to lift/push/pull minimum of 50 pounds.</li>
<li>May work in maintenance shop or outside.</li>
<li>Must be able to work in a shop where the environment is drafty, noisy, and dirty.</li>
<li>May be exposed to extreme noise from operating equipment.</li>
<li>May be exposed to electrical shock hazards or work near moving mechanical parts or vehicles.</li>
</ul></p><p></p>
<p>What we do Since 1863, the International Committee of the Red Cross (ICRC) has worked to preserve human dignity and relieve suffering caused by war and armed violence. In collaboration with our Red Cross and Red Crescent partners around the world, we do everything we can to deliver life-saving aid, reconnect families and locate missing people helping those who need it most, regardless of who they are and what side of the front line they are on. We engage with authorities and armed forces on all sides, often confidentially, pressing for access to detainees to improve their living conditions and urging compliance with international humanitarian law to protect non-combatants, including from digital threats.</p><p>Our values • At the ICRC, we value impact, collaboration, respect, and compassion. We seek candidates who demonstrate behaviors based on these shared values. For more information on the ICRC values, please visit this page. What we offer • Rewarding work in a humanitarian and multicultural environment • A two-week orientation course and other opportunities for further in-house training • Attractive social benefits • Join an ICRC talent pool and be considered for future assignments elsewhere</p><p>Purpose Prehospital Emergency Care Field Officer 2 contributes to implementing, running and monitoring the prehospital emergency and/or first-aid programme(s) in cooperation with the health team, according to the objectives set out during the delegation s annual planning process ( Planning for Results ) for a specific geographic area or field of activities. Based on her/his skills and experience, s/he has the capacity to oversee programmes with a degree of autonomy (e.g. delegations with remote management; delegations with no Health Coordinator).</p><h4>Accountabilities & functional responsibilities</h4><ul><li>Implements and monitors the Pre-Hospital Emergency Care (PHEC) program in Erbil Sub Delegation (ERB SD) Area of Responsibilties (AoR(, in line with the delegation's objectives, priorities and operational framework.</li><li>Conducts field assessments and regular visits to monitor program implementation, identify gaps and assess the quality of prehospital emergency care services.</li><li>Supports the strengthening of local emergency preparedness and response capacities through engagement with relevant health authorities and Emergency Medical Services (EMS) providers.</li><li>Builds and maintains effective working relationships with MoH/DoH authorities, EMS providers and other relevant stakeholders to facilitate coordination and program implementation.</li><li>Contributes to the development of realistic project proposals, activity plans and program priorities based on identified needs and operational assessments.</li><li>Supports the contextualization and implementation of ICRC technical guidelines, reference documents and tools related to PHEC.</li><li>Ensures systematic collection, analysis and reporting of program information using ICRC health reporting tools (e.g. DHiS, stock monitoring, MfR and ICRC Ambulance and ED Monitoring Tool).</li><li>Integrates Health Care in Danger (HCiD) considerations into engagement with supported EMS services and responders.</li><li>Ensures compliance with the agreed time allocation between ERB and SUL SD AoR through daily time reporting and regular coordination with line managers.</li></ul><h4>PHEC Program Implementation and Capacity Building</h4><ul><li>Supports the implementation and monitoring of PHEC activities within MoH-supported ambulance and EMS services in ERB SD AoR.</li><li>Works closely with the ICRC Emergency Medicine Specialist to support the development and implementation of key PHEC components, including electronic patient care records, emergency medical dispatch systems, referral pathways and quality-of-care mechanisms.</li><li>Contributes to the assessment of EMS capacity gaps and the planning and delivery of relevant capacity-building activities and technical training for MoH EMS personnel.</li><li>Conducts regular field follow-up with supported ambulance services to monitor operational practices, identify challenges and support improvements in the quality of prehospital care.</li><li>Participates in relevant technical training and Training of Trainers (ToT) activities to strengthen professional knowledge and support program implementation.</li></ul><p>Additional information • Job Title: Prehospital Emergency Care Field Officer 2 • Level: B2 • Duty Station : Iraq Erbil Sub Delegation • Reports to: Deputy Head of Sub Delegation • Duration of Contract: 12 Month fixed-term contract (renewable) • Date of Issue : 17 November 2026 • Deadline for applications : 30 November 2026</p><p>Reports to (role) • Deputy Head of Sub Delegation</p><p>People management responsibilities No</p><p>Relationships • Internally, interacts with health staff (Prehospital Emergency Care/First-Aid/Health Delegate, Health Coordinator), the Movement Cooperation Coordinator and non-health staff. • Externally, interacts with local prehospital emergency medical and first-aid authorities, international and local stakeholders (International Red Cross and Red Crescent Movement partners, United Nations agencies, non-governmental organizations, etc.) in his/her geographic area or field of responsibility, armed groups and beneficiaries.</p><p>Note Female candidates are strongly encouraged to apply. This position is open to national candidates. No Fee: ICRC DOES NOT CHARGE A FEE AT ANY STAGE OF THE RECRUITMENT PROCESS WHETHER APPLICATION, TESTS, INTERVIEWS OR PROCESSING.</p><p><strong>Desired Candidate Profile</strong></p><h4>Desired profile and skills</h4><ul><li>Strongly motivated by humanitarian work</li><li>Able to work under pressure in a potentially dangerous environment</li></ul><h4>Certifications / Education required</h4><ul><li>Bachelor s degree in paramedic science/paramedic practice, or two to three years vocational training as a paramedic. (An emergency medical technician (EMT) diploma is NOT sufficient).</li><li>Qualification as a trainer (e.g. in Basic Life Support (BLS), Basic Trauma Life Support (BTLS), Advanced Trauma Life Support (ATLS), Prehospital Trauma Life Support (PHTLS), Emergo Train System, Major Incident Medical Management and Support (MIMMS) or First Aid).</li><li>Additional studies in a relevant field (e.g. emergency medicine, public health) a strong asset.</li><li>Fluent in English, Kurdish and Arabic languages (written and spoken).</li></ul><h4>Professional experience required</h4><ul><li>At least three years work experience in prehospital emergency medical care, training/education and/or prehospital emergency care programme support.</li><li>Technical experience in training (prehospital emergency care and first aid).</li><li>Experience in resource-limited settings with other organizations or stakeholders.</li><li>Experience with prehospital and ambulance equipment.</li><li>Good knowledge of the assigned geographic area.</li><li>Strong interest in prehospital emergency care and a career in EMS services.</li></ul>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p>INTECH Process Automation is seeking a seasoned <strong>HVAC Technician</strong> to join our Operations & Maintenance (O&M) team. The selected candidate will be responsible for the <strong>maintenance, troubleshooting, inspection, and repair of HVAC and package cooling systems</strong> supporting analyzers, control rooms, ICSS, electrical/instrument rooms, and other critical facilities. Ensures reliable environmental conditions and safe operation of HVAC equipment.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform <strong>preventive and corrective maintenance</strong> on HVAC units, package cooling systems, split/ducted systems, and associated equipment.</li><li>Inspect and maintain <strong>compressors, condensers, evaporators, fans, filters, coils, belts, dampers, drains, and refrigerant circuits</strong>.</li><li>Monitor and record <strong>temperature, humidity, pressure, refrigerant condition, and operating parameters</strong>.</li><li>Troubleshoot and repair <strong>HVAC mechanical, electrical, control, and instrumentation faults</strong>.</li><li>Maintain environmental conditions for <strong>analyzer shelters, control rooms, ICSS rooms, equipment rooms, and other critical areas</strong>.</li><li>Check and maintain <strong>thermostats, sensors, controllers, contactors, relays, motors, and control panels</strong>.</li><li>Perform <strong>filter cleaning/replacement, coil cleaning, refrigerant checks, leak detection, and system servicing</strong>.</li><li>Support <strong>refrigerant recovery, charging, and handling</strong> in accordance with approved procedures and safety requirements.</li><li>Identify abnormal conditions, recurring failures, and equipment deterioration; perform <strong>basic troubleshooting and root-cause assessment</strong> and escalate major defects.</li><li>Verify HVAC performance after maintenance and ensure <strong>environmental conditions are restored before return to service</strong>.</li><li>Maintain accurate <strong>maintenance records, operating logs, checklists, work orders, and CMMS documentation</strong>.</li><li>Coordinate with <strong>Instrumentation, Electrical, ICSS, Analyzer, Operations, and Maintenance teams</strong> for equipment interfaces and shutdown activities.</li><li>Maintain HVAC tools, test equipment, spare parts, and consumables in <strong>safe and serviceable condition</strong>.</li><li>Follow <strong>PTW, LOTO, refrigerant safety, electrical safety, HSE, and procedures</strong>.</li></ul> </div>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p><b>Title:</b></p><br><br>Commissioning Manager<br><br><p><b>"Belong, Connect, Grow, with KBR!</b></p><br><br><br><p><b>The KBR team of teams delivers future-forward science, technology and engineering solutions and mission-critical services that help governments and companies around the world accomplish their most important objectives, while also helping achieve their sustainability goals.</b></p><br><br><p><b>KBR Sustainable Technology Solutions provides holistic and value-added solutions across the entire asset life cycle. These include world-class licensed process technologies, differentiated advisory services, deep technical domain expertise, energy transition solutions, high-end design and engineering capabilities, and smart solutions to optimize planned and operating assets."</b></p><br><br><br><p><b>Job Description</b>: Commissioning Manager</p><br><br><p><b>Company:</b> KBR</p><br><br><p><b>Location:</b> Iraq (28/28 Rotational Assignment)</p><br><br><br><p><b><u>Job Responsibility and Requirement</u></b></p><br><br><ul><li>The Commissioning Manager shall be responsible for the Commissioning deliverables of KBR Majnoon projects, managing team and resources to ensure the scope or work is executed in a safe timely manner in line with project schedule and milestones.</li><li>Manage and lead Commissioning team and vendors, monitoring progress and ensuring work execution is both safe and best practices.</li><li>Development of Commissioning execution plans, schedules and procedures.</li><li>Focal Start Up and Operational readiness communications with Management Team, Client and facilitate handover activities.</li></ul><br><p><b>Accountability / Expectations</b></p><br><br><ul><li>Lead by example and coach good HSE and safe working practices.</li><li>Develop Commissioning strategy and execution plans.</li><li>Develop Commissioning and input to the integrated schedule – in line with project timeline and milestones.</li><li>Develop Commissioning and Start-up procedures.</li><li>Coordinate between the Engineering, construction, and Operation teams to ensure that all systems are installed, tested, verifying readiness for RFSU claims.</li><li>Manage completion Systemization and implementation to ensure works can progress methodically and efficiently.</li><li>Manage resources to ensure preparation and review of commissioning procedures, completions system and RLMs.</li><li>Ensure test records of all commissioning activities, including test results, reports, and any issues encountered are accurate and compiled in line with completions strategies.</li><li>Ensure all commissioning dossiers and documentation is completed, updated, and ready for review and handover.</li><li>Manage Commissioning vendor requirements/</li><li>Develop Work Execution Flow Scheme (WEFS).</li><li>Develop readiness and ORA documentation, PSSR, PSUA, SOF to support RFSU Certification claims.</li><li>Develop Commissioning Consumables list and commissioning spares list.</li><li>Develop and implement Project to Asset Transfer Plan (P2A) plan comprising of physical assets with system turnover team and the Information Management Documents</li><li>Drive the Flawless Project Delivery (FPD) with a focused ownership on the FPD deliverables specific for the CSU areas</li><li>Manage and support interface with the Asset’s Operations & Maintenance during start up and handover.</li></ul><br><p><b><u>Experience required:</u></b></p><br><br><ul><li>20+ Years of experience in Oil & gas industry</li><li>Bachelor honours degree in a relevant engineering discipline from a recognised institution.</li><li>Master’s degree in relevant engineering discipline.</li></ul><br><br><br><br><br> </div>
<p>The Non-Destruction Inspection Technician (NDI) II inspects aerospace weapon systems components and support equipment for structural integrity using nondestructive inspection methods and performs fluid analysis.</p><p>• Determine test method and prepare fluids and parts for nondestructive inspection.</p><p>• Interpret nondestructive inspection test results and provide information about defects to repair center.</p><p>• Analyze wear metal content reports on engine lubricating oil and other fluids and recommend corrective action.</p><p>• Establish radiation areas for radiographic operations.</p><p>• Compute and monitor personal exposure areas for radiographic operations, and monitor personnel exposure data.</p><p>• Perform nondestructive inspection on structures, components, and systems.</p><p>• Detect flaws such as cracks, delamination s, voids, processing defects, and heat damage using penetrate testing, eddy current, magnetic particle, radiographic, optical, and ultrasonic test equipment.</p><p>• Determine metallurgical information of components according to alloy, temper, conductivity, and associated factors.</p><p>• Operate, maintain, and inspect nondestructive equipment.</p><p>• Perform operator maintenance and service inspections on shop equipment and tools.</p><p>• Ensure lock out and tag out procedures are accomplished prior to maintenance on equipment.</p><p>• Perform silver recovery functions.</p><p>• Handle and dispose of hazardous waste and materials.</p><p>• Perform other qualified duties as assigned.</p><p>Knowledge & Skills</p><p>• Previous experience in the maintenance, modification and repair of tactical aircraft systems of the type being serviced and their associated components (UH60, AH64, CH47).</p><p>• Have the skills and knowledge to set up and standardize equipment, conduct tests, interpret and evaluate for acceptance or rejection, and document.</p><p>• Thoroughly familiar with the scope and limitations of the technique/method in which they are certified.</p><p>• Capable of providing the necessary guidance and supervision to trainers and Level I personnel in the technique/method in which they are certified.</p><p>• Familiar with the codes, standards, and other contractual documents that control the method as utilized by the employer.</p><p>• Capable of developing written instructions from approved general procedures. Such instructions shall require final approval by a Level III.</p><p>• Knowledge of electrical, mechanical, electronic, hydraulic and pneumatic systems or other technology as applicable to fabrication, repair, operation and maintenance requirements.</p><p>• Efficient in record keeping and preparation of reports; capable of reviewing other people's work and determining accuracy and conformity to standards.</p><p>• Proficient in the use of the Unit Level Logistics System-Aviation Enhanced (ULLS-AE), the current maintenance management system utilized to maintain Army aircraft forms and records.</p><p>• Comprehensive knowledge of aircraft mechanical component troubleshooting/repair procedures and replacement of components.</p><p>• Thorough knowledge of aircraft sheet metal/structural modification and repair and the ability to determine functionality of non-complex electrical systems.</p><p>• Detailed knowledge of aircraft unique tools such as test equipment, torque wrenches, dial indicators, micrometers, cable tensiometers, sheet metal brakes and sheers, etc. is required.</p><p>• Ability to provide technical support to structural/mechanical engineers and customers.</p><p>• Excellent organizational skills in prioritizing workload to meet aircraft delivery schedule.</p><p>Physical Requirements/Working Environment</p><p>• Must be able to walk and stand on level and/or inclined surfaces for extended periods throughout the day</p><p>• Must be able to climb stairs, ramps, ladders, and work stands</p><p>• Must be able to crouch, crawl, grasp or handle objects, use finger dexterity, bend elbow/knee and reach above/below shoulders</p><p>• May be required to lift heavy objects whose weight may exceed 50 pounds</p><p>• Must be able to type using a standard keyboard to communicate through e-mail and various software applications</p><p>• Will handle dirty parts and lubricants</p><p>• Will be required to wear proper Personal Protective Equipment (PPE)</p><p>• Must be able to pass a Respirator Physical and Fit Test qualification</p><p>• May be required to operate power vehicles, machinery, hand tools, ground support equipment, fork lift, etc.</p><p>• Must be able to lift/push/pull minimum of 50 pounds</p><p>• May work in maintenance shop or outside</p><p>• Must be able to work in a shop where the environment is drafty, noisy, and dirty</p><p>• May be exposed to extreme noise from operating equipment</p><p>• May be exposed to electrical shock hazards or work near moving mechanical parts or vehicles.</p><p><strong>Desired Candidate Profile</strong></p><p>Minimum Requirements :</p><ul><li>High school diploma or equivalent required.</li><li>U.S. military technical school or specialized training course is desired, certification of education level is required.</li><li>Completion of a initial Non Destructive Inspection Level II training Course and current basic qualification.</li><li>Three (3) or more years experience as an aviation inspector and a minimum of one year experience on the assigned(MDS) airframe . (UH60, AH64, CH47 )</li><li>Shall be trained and qualified per NAS 410 or ASNT-CP-189 to the level assigned.</li><li>Must be in possession of a U.S. Passport with 3 years of validity remaining at the time of hire and be able to travel internationally.</li><li>Ability to obtain and maintain a US Government Security Clearance, NAC-I T1 Public Trust.</li><li>** US Citizenship is required to obtain a T1/CAC NACI Clearance.</li><li>Able to clear CENTCOM Medical requirements for deployment.</li><li>Ability to obtain and maintain Iraq Visa</li></ul>
<h2 class="h5">Job description</h2>
<div class="t-break" data-jb-field="description">
<p><b>Are you ready to shape the future with confidence?</b></p><br><p>Here at EY, you’ll have the chance to build a truly exceptional experience. We’ll empower you with the latest technology, surround you with high-performing teams, and provide the global scale and diverse and inclusive culture you need to discover your full potential. Through our coaching and training programs, you’ll develop the skills you need to stay relevant today and, in the future, – all while building a network of colleagues, mentors, and leaders who will be on the journey with you at EY and beyond.</p><br><p><b>The opportunity: your next adventure awaits </b></p><br><p>You will be joining one of the most dynamic and people-focused teams in the industry. In <b>People Advisory Services (PAS)</b>, we help organizations transform their workforce strategies, enhance employee experiences, and navigate the complexities of global mobility and compliance. Our work spans HR transformation, payroll, rewards, learning, immigration, tax compliance, and international mobility—delivering insights that align talent with business strategy and drive sustainable growth. </p><br><p><b>What we look for: </b></p><br><ul><li><b>You have an agile, growth-oriented mindset. </b>What you know matters. But the right mindset is just as important in determining success. We’re looking for people who are innovative, can work in an agile way and keep pace with a rapidly changing world.</li><li><b>You are curious and purpose driven.</b> We’re looking for people who see opportunities instead of challenges, who ask better questions to seek better answers.</li><li><b>You are inclusive.</b> We’re looking for people who seek out and embrace diverse perspectives, who value differences, and team inclusively to build safety and trust. </li><li><b>Qualifications:</b> <ul><li>Bachelor’s or master’s degree completed in Accounting, Industrial Engineering, Business Administration, or any business-related major within the past 18 months</li><li>Nationals only to be considered</li></ul></li></ul><p><b>What’s in it for you: </b></p><br><ul><li>Accelerate your technical capabilities and transformative leadership skills with future-focused courses and development programs.</li><li>Broaden your horizons by working on highly integrated teams across the globe and collaborate with people of diverse backgrounds — both professionally and culturally.</li><li>Bring out the best in yourself with continuous investment in your personal well-being and career development.</li><li>Develop your own personal purpose and help us create a positive ripple effect on our teams, our business, clients and society.</li></ul><p><b>Are you ready to shape your future with confidence? Apply today.</b></p><br><b>Step 1: Apply</b><ul><li>Please complete the online application and answer all the questions.</li></ul><b>Step 2: Test</b><ul><li>If selected, you will receive an invitation to complete the EY online assessments. </li></ul><b>Step 3: On Demand Interview</b><ul><li>Upon passing the assessments, you will receive an invitation for an initial interview.</li></ul><b>Step 4: Attend</b><ul><li>If shortlisted, you may be invited to attend a recruitment day or a technical interview. </li></ul><b>Step 5: Receive</b><ul><li>If successful, you will receive an offer to join EY and begin your career at one of the best companies to work for.</li></ul><p>Are you ready to shape your future with confidence? Apply today. </p><br><p>To help create an equitable and inclusive experience during the recruitment process, please inform us as soon as possible about any disability-related adjustments or accommodations you may need.</p><br><p>For further information, and to apply, please visit our website via the “Apply” button below.</p><br><br> </div>
<p><h4>Responsibilities</h4>
<p>The Air Crew Life Support Technician performs inspections, maintenance, and troubleshooting tasks on T-6A aircraft.</p>
<ul>
<li>Perform launch, recovery, scheduled, and unscheduled inspections and maintenance.</li>
<li>Perform preflight, through-flight, and BPO inspections; ground handling; minor maintenance; and servicing.</li>
<li>Perform routine troubleshooting, installation, repair, and maintenance of aircraft electromechanical systems and components at the organizational level of maintenance.</li>
<li>Service aircraft and perform end-of-runway, post-flight, preflight, through-flight, and phase inspections.</li>
<li>Troubleshoot and maintain aircraft structures, systems, components, and related equipment. Remove and install aircraft components.</li>
<li>Perform scheduled and unscheduled maintenance and inspections on company aircraft in accordance with FAA regulations, manufacturer and company maintenance manuals, and procedures.</li>
<li>Service, operate, and maintain ground support equipment. Clean aircraft interiors and exteriors and work areas.</li>
<li>Complete all maintenance documentation accurately.</li>
<li>Perform other position-related duties as assigned or requested.</li>
</ul>
<h4>Minimum position knowledge, skills, and abilities required</h4>
<ul>
<li>At least four years of directly related heavy aircraft maintenance experience is highly desired. Experience must include following applicable aircraft servicing procedures, maintenance manuals, and parts catalogs.</li>
<li>Experience with OBOGS systems and T-6 life support is required.</li>
<li>Read, interpret, and use manufacturer and aircraft maintenance manuals, service bulletins, blueprints, wiring and schematic diagrams, data tables, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.</li>
<li>Inspect, repair, and operate ground support and auxiliary equipment.</li>
<li>Possess a current state-issued driver’s license.</li>
<li>Be able to obtain and maintain a U.S. passport for facility credentials and authorization. U.S. citizenship is required for facility credentials and authorization at this work site.</li>
</ul>
<h4>Work environment, physical demands, and mental demands</h4>
<ul>
<li>Carry and lift up to 50 pounds overhead.</li>
<li>Walk, climb, stand, stoop, stretch, and squat to move equipment, board and deboard aircraft, perform maintenance using ladders, and work atop and below aircraft.</li>
<li>Work at high altitudes when performing flight attendant duties.</li>
<li>Work primarily outdoors in a high-noise environment.</li>
<li>Perform maintenance in low-light areas and operate support equipment after daylight hours. Work occasionally in inclement weather.</li>
</ul></p><p></p>
<div><br></div><p><strong>Operation Supervisor</strong></p> <p>Would you like to be part of the most international company in the world? A company operating in more than 220 countries worldwide and has been pioneering cross-border express shipping since 1969. Would you like to be part of a business that connects people across the globe and want to make a difference? Then waste no time and join our amazing team at DHL Group. DHL Global Forwarding, Freight (DGFF) is the Group's air, ocean, and road freight specialist. We offer standardized transport as well as highly specialized end-to-end solutions to customers in a wide range of industries globally.</p> <p><em>Who finds the right solutions at the right time? You do! Then we need to hear from you. Grab this unique opportunity to join the best Freight forward company.</em> DHL Global Forwarding has an opening for a <strong>Operations Supervisor </strong>in<strong> Kirkuk, Iraq. </strong></p> <p>Join us in connecting people and improving lives!</p> <p><strong>In this Operations Supervisor position </strong></p> <ul> <li>Individual contributor with the ability to work under moderate supervision</li> <li>Requires basic knowledge of job procedures and tools obtained through work experience and may require vocational or technical education</li> </ul> <ul> <li>Problems are typically of a routine nature, but may at times require interpretation or deviation from standard procedures</li> </ul> <ul> <li>Under supervision, support delivery of operations processes and activities</li> <li>Provide administrative support to the transport and distribution unit or department</li> <li>Keep vehicles and equipment in working order through a comprehensive program</li> <li>Collect/ deliver shipments within specified time by planning routes, liaising with external departments, timely communications, etc.</li> <li>Interact with import/ export departments in anticipation of changes, make relevant changes and communicate adjustments to relevant stakeholders</li> <li>Carry out proper loading/ unloading of the loading unit/ loading security</li> <li>Record loading/ unloading activities at customer end through appropriate tools scanning application, phones, etc.</li> <li>Enter data into database or computerized system to maintain up-to-date stock records</li> <li>Access stored information, place orders or respond to enquiries such as inventory levels or delivery schedules</li> <li>Follow and achieve compliance with established procedures and ensure proper usage of operations processes and policies</li> </ul> <p>Resolve recurring issues faced during delivery as per defined processes, systems and methods</p> <p><strong>Now, here is what we need from you!</strong></p> <table> <tbody> <tr> <td> <p><strong> Qualifications & Key Requirements</strong></p> </td> </tr> <tr> <td> <p><strong>Education Level</strong></p> </td> </tr> <tr> <td> <p>Vocational/Specialized/Technical/Certification</p> </td> </tr> <tr> <td> <p><strong>Experience Level</strong></p> </td> </tr> <tr> <td> <p>less than 2 years</p> </td> </tr> </tbody> </table> <p><strong>We offer:</strong></p> <ul> <li>Opportunities in a global company where you can contribute your ideas and skills to move towards our shared goals.</li> <li>Possible further career development</li> <li>Competitive salary</li> </ul> <p><strong>Why join DHL Global Forwarding?</strong></p> <p>We are part of DHL Group, the world’s leading logistics provider with operations in over 220 countries. Visit our career site on the web at <a href="https://www.logistics.dhl/us-en/home/careers.html">https://www.logistics.dhl/us-en/home/careers.html</a></p> <p>Our <strong>TOP EMPLOYER prestigious certification</strong> attests to our best-in-class efforts to attract and retain talent by fostering a positive work environment and encouraging personal and professional development among employees. The development of talented women in our organization is an ongoing key focus area.</p> <p>We aspire to become the undisputed leader in our industry, <strong>when people think of forwarding; we want them to think DGF </strong>because we have:</p> <ul> <li>The<strong> largest global network</strong> with more than 30,000 passionate employees</li> <li>The most <strong>efficient processes</strong> and <strong>fastest response times</strong></li> <li>The <strong>best solutions</strong> and <strong>best customer service</strong></li> </ul> <p><strong>Our Vision: </strong>The Logistics Company for the World.</p> <p><strong>Our Mission: </strong>Excellence. Simply Delivered.<br> <strong>Our Purpose: </strong>Connecting People, improving lives.<br> <strong>Our Values: </strong>Respect & Results<br> <strong>Our Goals: </strong>Employer, Provider, and Investment of Choice, Living Responsibility</p> <p><em>DHL Global Forwarding is an equal opportunity employer. We evaluate qualified applicants without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, veteran status, and other legally protected characteristics. </em></p>
Receive email alerts for Technical Analysts Jobs in Iraq jobs
You can cancel your email alert at anytime