وظائف فني كهرباء في العراق

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Site E&amp;I Construction lead-(Oil, Gas &amp; Water)<br><br><p><b>Job Description</b>: Construction E&amp;I Lead</p><br><br><p>Company: KBR</p><br><br><p>Location: Iraq (28/28 Rotational Assignment)</p><br><br><p>Nationality: Any</p><br><br><br><p>The Lead Construction Engineer (E&amp;I) will drive construction readiness, optimize field execution strategies, and ensure effective coordination between engineering, procurement, construction, commissioning, and operations. This position requires a seasoned professional capable of leading multidisciplinary teams and consistently achieving project safety, cost, schedule, and quality objectives</p><br><br><br><p><b>Accountability/ Expectations</b></p><br><br><ul><li>Enhance construction safety performance by promoting modularization, standardized assemblies, pre‑fabricated E&amp;I modules, and off‑site construction to reduce field exposure.</li><li>Develop brownfield and greenfield construction strategies, including tie‑in planning, SIMOPS coordination, shutdown integration, and live‑plant execution methodologies.</li><li>Identify and resolve E&amp;I construction challenges such as cable routing conflicts, hazardous area compliance issues, and instrument accessibility constraints.</li><li>Monitor field productivity using discipline-specific KPIs (cable pulling rates, termination progress, loop completion curves, energization milestones).</li><li>Lead construction planning, ensuring detailed sequencing for electrical load transfer, instrument migration, and control system cutover activities.</li><li>Provide constructability input into electrical single-line diagrams, cable block diagrams, instrument indexes, control system architecture, and hazardous area layouts.</li><li>Ensure design decisions align with HSE, cost, schedule, and quality requirements, validating field feasibility and installation constraints.</li><li>Facilitate Constructability Reviews focused on cable routing, instrument maintainability, equipment lifting constraints, and hazardous area compliance.</li><li>Serve as the primary E&amp;I construction interface from project inception through field execution.</li><li>Collaborate with Construction Management to develop execution plans covering power distribution, loop testing, control system migration, and cable management.</li><li>Manage multiple concurrent E&amp;I work fronts, ensuring resource leveling and contractor performance oversight.</li><li>Ensure engineering and procurement deliverables (SLDs, ILDs, P&amp;IDs, I/O lists, datasheets, cable drums, switchgear, instrument panels) align with construction sequencing and commissioning priorities.</li><li>Prepare detailed E&amp;I work packages including cable schedules, termination sheets, loop diagrams, installation drawings, and material take-offs.</li><li>Review and update work package documentation, red-line markups, as-built records, and test documentation.</li><li>Ensure compliance with IEC/NEC standards, ATEX/IECEx requirements, grounding and bonding standards, and project-specific electrical safety rules.</li><li>Support commissioning teams in developing energization plans, loop testing protocols, instrument calibration procedures, and control system functional testing.</li><li>Ensure construction activities integrate seamlessly with commissioning, operations, and other discipline interfaces.</li><li>Advocate for cold-work strategies such as pre-terminated instrument cables, plug-and-play analyzer shelters, and pre-assembled marshalling cabinets.</li><li>Align construction execution with project scope, quality, cost, and schedule targets.</li><li>Ensure engineering and procurement deliverables meet construction and handover requirements.</li><li>Implement Work Face Planning to ensure crews receive fully validated work packages.</li><li>Support interfaces with operations, ensuring safe and efficient brownfield and greenfield execution.</li><li>Ensure final designs incorporate construction risk assessments and economic considerations.</li></ul><br><p><b>Education</b></p><br><br><p>BSc. in Instrumentation, Electrical Engineering, or a related discipline.</p><br><br><br><p><b>Experience Requirements</b></p><br><br><p>Minimum 10 + years experience in Oil &amp; Gas E&amp;I design, construction, and commissioning.</p><br><br><br><p>Strong understanding of:</p><br><br><ul><li>LV/MV electrical distribution</li><li>Instrumentation installation and calibration</li><li>Loop testing and commissioning workflows</li><li>Proficiency in productivity measurement and resource-based planning (Level 4 Scheduling).</li><li>Proven leadership and supervisory experience in managing E&amp;I construction teams and contractors.</li><li>Strong organizational skills with the ability to manage multiple work fronts and shifting priorities.</li><li>High attention to detail with a focus on quality, accuracy, and safe execution.</li></ul><br><br><br><br> </div>

<p><h4>Essential responsibilities:</h4> <p>Aerostat operators/user-level maintainers will participate in the overall, hands-on operation of the aerostat system including launch, in-flight, recovery, and moored activities.</p> <p>Candidates will perform all functions to operate the PGSS/PTDS, an aerostat mounted intelligence, surveillance, and reconnaissance (ISR) platform, its mobile mooring platform (MMP), sensor payload(s), communications and navigation systems as well as associated support equipment (boom lift, forklift, all terrain vehicles (ATVs), and electrical power generators).</p> <p>Candidate will perform user-level maintenance functions including performing hands-on preventative maintenance checks and services (PMCS), troubleshooting, removing and replacing line replaceable units (LRUs), and removing and replacing payloads.</p> <p>Candidate must possess a diverse range of skills with the ability to quickly adapt to new situations. Tasks will be performed under direction of higher classified technicians and/or site personnel.</p> <h4>Minimum requirements:</h4> <ul> <li>High school diploma or equivalent is required.</li> <li>Two-year associate’s degree in a technical field from an accredited college can substitute for work experience.</li> <li>Must have an active secret US government clearance or the ability to obtain a secret clearance. Note: US citizenship is required to obtain a secret clearance.</li> <li>Must have a valid U.S. passport with a minimum of one year remaining.</li> <li>Must have valid US driver’s license.</li> <li>Knowledge of and experience in the operations of hardware systems and components.</li> <li>Experience in fault detection, isolation, and correction of hardware systems and individual components.</li> <li>Ability to perform routine system maintenance and analysis functions including: hardware configurations; adding, removing and replacing hardware components; use of hardware and software diagnostic testing tools; reading of electronic circuit schematics; and repairing printed circuit boards.</li> <li>At least one (1) year previous aerostat experience OR two (2) years of experience in the following areas may be substituted in lieu of aerostat experience:</li> </ul> <p><strong>1) Electrical maintenance mechanic</strong></p> <ul> <li>Possess at least two (2) years aerostat experience as an operator at the 20 series level or greater from Army MOS 35F (Intelligence Analyst), 35G (Geospatial Intelligence Imagery Analyst), 35H (Common Ground System Analyst), 96R (Ground Surveillance Systems Operator), 96U (Unmanned Aerial Vehicle Operator), or military branch equivalent.</li> <li>Two years of hands-on experience in performing operations and maintenance tasks either on an aerostat system or a related industry/military equivalent is required.</li> <li>Must be qualified at the 10 series or greater level (via military or civilian technical schools) is required.</li> <li>Ability to read electronic schematics.</li> <li>O&M of electro-mechanical equipment to include one or more of the following: <ul> <li>Hydraulic/servo valves</li> <li>Hydraulic actuators, control systems</li> <li>Test and diagnostic equipment</li> </ul> </li> </ul> <p><strong>2) Networking, IT & information systems</strong></p> <ul> <li>Two years’ experience is required.</li> <li>Must be qualified at the 10 series or greater level; MOS 25B/F or other military branch equivalent or industry occupational specialties as a CISCO Network Administrator; Army MOS 25L/N or other military branch equivalent or industry occupational specialties as a Network Installation (BICSI or Network + or Comp T Certification) will be considered.</li> <li>CCIE certification with fiber optic certification is preferred.</li> </ul> <p><strong>3) Mechanical maintenance</strong></p> <ul> <li>Mechanical maintenance with qualifications at the 10 series or greater from U.S. Army MOS 94D/X and 91/B/S/W or other military branch equivalent, or industry occupational specialties such as National Institute for Automotive Service Excellence (ASE) Certified Truck Mechanic or Federal Aviation Administration (FAA) General Mechanic 1 or greater.</li> <li>Two years of hands-on experience on an aerostat system or a related industry/military equivalent is required.</li> <li>O&M of mechanical equipment to include one or more of the following: hydraulic systems, winch systems, tether/cable handling systems, industrial generator sets, power switch gear, HVAC, cranes aerial lift, forklift, industrial generator sets.</li> </ul> <h4>Physical requirements:</h4> <ul> <li>Requires the ability to regularly lift up to 50 lbs.</li> <li>Requires the ability to regularly climb extension ladders, roof ladder, stepladders, and stairs at least 10 times during shift.</li> <li>Requires the flexibility to bend/stoop, squat repetitive during shift.</li> <li>Requires the ability to regularly kneel repetitive for shift.</li> <li>Requires the ability to move in a 90-degree fashion on a repetitive basis for shift.</li> <li>Requires the ability to stretch/reach on a repetitive basis for shift.</li> <li>Requires the ability to walk extensively throughout the plant during shift.</li> <li>Requires the ability to interact with all clients in a professional and friendly manner despite periods of stress.</li> </ul> <h4>Medical requirements:</h4> <p>Successfully complete and pass the medical and dental examinations as required by the employer and customer for deployment to Iraq.</p> <p>Must maintain physical and dental requirements for the duration of the deployment.</p> <h4>Working and living conditions:</h4> <p>This position may be located in a war zone, in an environment with harsh and dangerous working and living conditions. While performing the duties of this job, the employee may regularly be exposed to extreme and austere desert-like environment. Temperatures can reach 120-130 degrees Fahrenheit/50-55 degrees Celsius during the summer months. Employees must be willing and able to perform regular job requirements in this austere, extreme environment, as well as willing and able to deploy to CENTCOM, EUCOM, and AFRICOM for extended periods. Work schedules are a minimum of 6 days per week and 10 hours per day, while some jobs have higher daily and weekly minimums.</p></p><p></p>

<p><h4>Essential responsibilities:</h4> <p>Aerostat operators/user-level maintainers will participate in the overall, hands-on operation of the aerostat system including launch, in-flight, recovery, and moored activities.</p> <p>Candidates will perform all functions to operate the PGSS/PTDS, an aerostat mounted intelligence, surveillance, and reconnaissance (ISR) platform, its mobile mooring platform (MMP), sensor payload(s), communications and navigation systems as well as associated support equipment (boom lift, forklift, all terrain vehicles (ATVs), and electrical power generators).</p> <p>Candidate will perform user-level maintenance functions including performing hands-on preventative maintenance checks and services (PMCS), troubleshooting, removing and replacing line replaceable units (LRUs), and removing and replacing payloads.</p> <p>Candidate must possess a diverse range of skills with the ability to quickly adapt to new situations. Tasks will be performed under direction of higher classified technicians and/or site personnel.</p> <h4>Minimum requirements:</h4> <ul> <li>High school diploma or equivalent is required.</li> <li>Two-year associate’s degree in a technical field from an accredited college can substitute for work experience.</li> <li>Must have an active secret US government clearance or the ability to obtain a secret clearance. Note: US citizenship is required to obtain a secret clearance.</li> <li>Must have a valid U.S. passport with a minimum of one year remaining.</li> <li>Must have valid US driver’s license.</li> <li>Knowledge of and experience in the operations of hardware systems and components.</li> <li>Experience in fault detection, isolation, and correction of hardware systems and individual components.</li> <li>Ability to perform routine system maintenance and analysis functions including: hardware configurations; adding, removing and replacing hardware components; use of hardware and software diagnostic testing tools; reading of electronic circuit schematics; and repairing printed circuit boards.</li> <li>At least one (1) year previous aerostat experience OR two (2) years of experience in the following areas may be substituted in lieu of aerostat experience:</li> </ul> <p><strong>1) Electrical maintenance mechanic</strong></p> <ul> <li>Possess at least two (2) years aerostat experience as an operator at the 20 series level or greater from Army MOS 35F (Intelligence Analyst), 35G (Geospatial Intelligence Imagery Analyst), 35H (Common Ground System Analyst), 96R (Ground Surveillance Systems Operator), 96U (Unmanned Aerial Vehicle Operator), or military branch equivalent.</li> <li>Two years of hands-on experience in performing operations and maintenance tasks either on an aerostat system or a related industry/military equivalent is required.</li> <li>Must be qualified at the 10 series or greater level (via military or civilian technical schools) is required.</li> <li>Ability to read electronic schematics.</li> <li>O&M of electro-mechanical equipment to include one or more of the following: <ul> <li>Hydraulic/servo valves</li> <li>Hydraulic actuators, control systems</li> <li>Test and diagnostic equipment</li> </ul> </li> </ul> <p><strong>2) Networking, IT & information systems</strong></p> <ul> <li>Two years’ experience is required.</li> <li>Must be qualified at the 10 series or greater level; MOS 25B/F or other military branch equivalent or industry occupational specialties as a CISCO Network Administrator; Army MOS 25L/N or other military branch equivalent or industry occupational specialties as a Network Installation (BICSI or Network + or Comp T Certification) will be considered.</li> <li>CCIE certification with fiber optic certification is preferred.</li> </ul> <p><strong>3) Mechanical maintenance</strong></p> <ul> <li>Mechanical maintenance with qualifications at the 10 series or greater from U.S. Army MOS 94D/X and 91/B/S/W or other military branch equivalent, or industry occupational specialties such as National Institute for Automotive Service Excellence (ASE) Certified Truck Mechanic or Federal Aviation Administration (FAA) General Mechanic 1 or greater.</li> <li>Two years of hands-on experience on an aerostat system or a related industry/military equivalent is required.</li> <li>O&M of mechanical equipment to include one or more of the following: hydraulic systems, winch systems, tether/cable handling systems, industrial generator sets, power switch gear, HVAC, cranes aerial lift, forklift, industrial generator sets.</li> </ul> <h4>Physical requirements:</h4> <ul> <li>Requires the ability to regularly lift up to 50 lbs.</li> <li>Requires the ability to regularly climb extension ladders, roof ladder, stepladders, and stairs at least 10 times during shift.</li> <li>Requires the flexibility to bend/stoop, squat repetitive during shift.</li> <li>Requires the ability to regularly kneel repetitive for shift.</li> <li>Requires the ability to move in a 90-degree fashion on a repetitive basis for shift.</li> <li>Requires the ability to stretch/reach on a repetitive basis for shift.</li> <li>Requires the ability to walk extensively throughout the plant during shift.</li> <li>Requires the ability to interact with all clients in a professional and friendly manner despite periods of stress.</li> </ul> <h4>Medical requirements:</h4> <p>Successfully complete and pass the medical and dental examinations as required by the employer and customer for deployment to Iraq.</p> <p>Must maintain physical and dental requirements for the duration of the deployment.</p> <h4>Working and living conditions:</h4> <p>This position may be located in a war zone, in an environment with harsh and dangerous working and living conditions. While performing the duties of this job, the employee may regularly be exposed to extreme and austere desert-like environment. Temperatures can reach 120-130 degrees Fahrenheit/50-55 degrees Celsius during the summer months. Employees must be willing and able to perform regular job requirements in this austere, extreme environment, as well as willing and able to deploy to CENTCOM, EUCOM, and AFRICOM for extended periods. Work schedules are a minimum of 6 days per week and 10 hours per day, while some jobs have higher daily and weekly minimums.</p></p><p></p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p>INTECH Process Automation is seeking a Seasoned<strong> Commissioning Technician (Electrical) </strong>to join our Operations &amp; Maintenance (O&amp;M) team. The selected candidate will be responsible for <strong>electrical pre-commissioning, testing, inspection, rectification, and documentation</strong> under approved procedures and Engineer supervision. Ensure electrical systems supporting instrumentation and ICSS are safely tested and ready for energization and handover.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform assigned <strong>electrical pre-commissioning and commissioning tests</strong> under Engineer supervision.</li><li>Conduct <strong>continuity, insulation resistance (IR), earth/grounding, polarity, and functional tests</strong>.</li><li>Inspect and verify <strong>cables, terminations, glands, panels, connections, and labeling</strong>.</li><li>Perform checks on <strong>UPS, battery systems, control power supplies, and distribution panels</strong>.</li><li>Support testing of electrical power supplies serving <strong>Instrumentation, ICSS, DCS, SIS, PLC, and F&amp;G systems</strong>.</li><li>Identify and rectify approved <strong>electrical defects and punch-list items</strong>.</li><li>Support <strong>LOTO, isolation, de-energization, energization, and safe reinstatement</strong> activities.</li><li>Maintain <strong>test equipment, meters, tools, cables, and commissioning consumables</strong>.</li><li>Complete <strong>test sheets, checklists, punch records, inspection records, and commissioning documentation</strong>.</li><li>Report failed tests, defects, abnormal conditions, and unresolved issues to the <strong>Commissioning Engineer</strong>.</li><li>Coordinate with <strong>Electrical, Instrumentation, ICSS, Operations, Construction, HSE, and vendors</strong>.</li><li>Comply with <strong>PTW, LOTO, electrical safety, HSE, quality, and Company requirements</strong>.</li></ul> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <strong>Position: Electrical &amp; Instrumentation Technician - VFD Systems</strong><br> Location:&nbsp;Kirkuk, Iraq<br> Employment Type:&nbsp;1 years Contract role<br> Rotation- 6 week on /3 Week off<br> <br> <strong>Job Purpose</strong><br> Responsible for installation, maintenance, operation, troubleshooting, and repair of electrical, instrumentation, control systems, and VFD used in jet pump surface operations.<br> <br> <strong>Key Responsibilities</strong><ul><li>Install and maintain VFD-driven pumping systems.</li><li>Troubleshoot electrical and instrumentation faults.</li><li>Configure and commission VFDs and PLC-based control systems.</li><li>Perform calibration of pressure, flow, temperature, and level instruments.</li><li>Conduct preventive maintenance and inspection of electrical equipment.</li><li>Read and interpret electrical schematics and loop diagrams.</li><li>Diagnose communication issues between field instruments and control systems.</li><li>Support operational startups and equipment commissioning.</li></ul><strong>Required Qualifications</strong><ul><li>Diploma in Electrical, Electronics, or Instrumentation Engineering.</li><li>Minimum 3-5 years of oilfield experience.</li><li>Strong knowledge of:<ul><li>VFD programming and troubleshooting</li><li>MCC panels and switchgear</li><li>PLC systems</li><li>Instrument calibration</li><li>Electrical maintenance and fault finding</li><li>Control systems</li></ul></li><li>Experience with high-pressure pumping operations is preferred.</li></ul><strong>Preferred Skills</strong><ul><li>ABB, Siemens, Schneider, or Allen-Bradley VFD experience.</li><li>PLC troubleshooting experience.</li></ul>Hazardous area electrical certification is an advantage<br>With over 90 years' combined experience, NES Fircroft (NES) is proud to be the world's leading engineering staffing provider spanning the Oil &amp; Gas, Power &amp; Renewables, Chemicals, Construction &amp; Infrastructure, Life Sciences, Mining and&nbsp;Manufacturing&nbsp;sectors worldwide. With more than 80 offices in 45 countries, we are able to provide our clients with the engineering and technical expertise they need, wherever and whenever it is needed. We offer contractors far more than a traditional recruitment service, supporting with everything from securing visas and work permits, to providing market-leading benefits packages and accommodation, ensuring they are safely and compliantly able to support our clients. <br><br> </div>

<p><h4>Essential responsibilities:</h4> <p>The avionics technician performs aircraft maintenance to include inspection, operational test, repair, modification and replacement of aircraft electrical/avionics systems and components. Applies technical knowledge and skills to troubleshoot electrical/avionics discrepancies.</p> <ul> <li>Possess in-depth knowledge of applicable maintenance/technical manuals and publications, and special tools and test equipment. Must be familiar with operational capabilities and limitations of electrical/avionics systems.</li> <li>Possess a high degree of expertise of aircraft electrical/avionics systems.</li> <li>Performs the inspection, testing, troubleshooting, repair, modification and rewiring as required of complex avionics/electrical systems and subsystems discrepancies and modifications.</li> <li>Use schematic diagrams, blueprint drawings, maintenance manuals and factory publications to operate, modify, test and repair aircraft electrical/avionics systems.</li> <li>Utilize test equipment to include but not limited to digital volt/amp meter, transponder ramp tester, fuel quantity tester, ITT calibration test set, and other test equipment required in the troubleshooting, modification, and repair of avionics/electrical systems.</li> <li>Order parts and materials.</li> <li>Obtain and maintain qualification as a plane captain and any associated licenses/qualifications necessary to perform the duties of an OMAT2.</li> <li>Operate ground support equipment.</li> <li>Identify and treat avionics/electrical corrosion.</li> <li>Perform aircraft jacking and hoisting as required.</li> <li>Perform certification and re-certification of altimeter systems.</li> <li>Perform calibration of directional guidance systems.</li> <li>Required to perform collateral duty inspections.</li> <li>Must obtain and keep current turn qualification.</li> <li>Maintain cleanliness of the work center.</li> <li>Comply with foreign object damage (FOD), egress familiarization, and hazardous waste and tool control programs.</li> <li>Comply with all established general and industrial safety rules and regulations as applicable to the contract, facility, and job assignment.</li> <li>Assist as directed to ensure safety, security and preservation of government/company owned equipment.</li> <li>Present a courteous and professional demeanor when dealing with customers.</li> <li>Furnish and maintain own hand tools.</li> <li>Operate portable firefighting equipment.</li> <li>Operate aircraft ground servicing equipment including vehicles, tugs, tractors, servicing carts, aircraft jacks and hoists, test equipment, hand tools, power tools.</li> <li>Perform all other position related duties as assigned or requested.</li> </ul> <h4>Minimum qualifications:</h4> <ul> <li>Satisfactory completion of U.S. Armed Forces aircraft avionics school or other schools with equivalent curriculum or three (3) years of on-the-job training and/or experience working with similar avionics systems and components is required.</li> <li>Graduation from high school or GED required.</li> <li>Must be able to meet any government/company licensing/qualification requirements for the position.</li> <li>Must have an FAA Airframe and Powerplant (A&P) license.</li> <li>Must have three (3) years’ experience in T6 aircraft electrical/avionics maintenance including avionics corrosion detection, treatment and prevention, performing maintenance on avionics and/or electrical systems, utilizing tools, blueprints, drawings, wiring diagrams, schematics and normal safety requirements.</li> <li>Demonstrate a basic knowledge of aircraft systems and nomenclature.</li> <li>Possess working knowledge and skill in the use of basic tools and test equipment.</li> <li>Must be familiar with the operational capabilities and limitations of electrical/avionics systems.</li> <li>Possess a working knowledge of the detection, prevention, and treatment of corrosion.</li> <li>Must be able to read, write, understand, and communicate the English language and follow verbal and written instruction.</li> <li>Must obtain and keep current turn qualification.</li> </ul></p><p></p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p>INTECH Process Automation is seeking a seasoned <strong>HVAC Technician</strong> to join our Operations &amp; Maintenance (O&amp;M) team. The selected candidate will be responsible for the <strong>maintenance, troubleshooting, inspection, and repair of HVAC and package cooling systems</strong> supporting analyzers, control rooms, ICSS, electrical/instrument rooms, and other critical facilities. Ensures reliable environmental conditions and safe operation of HVAC equipment.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul><li>Perform <strong>preventive and corrective maintenance</strong> on HVAC units, package cooling systems, split/ducted systems, and associated equipment.</li><li>Inspect and maintain <strong>compressors, condensers, evaporators, fans, filters, coils, belts, dampers, drains, and refrigerant circuits</strong>.</li><li>Monitor and record <strong>temperature, humidity, pressure, refrigerant condition, and operating parameters</strong>.</li><li>Troubleshoot and repair <strong>HVAC mechanical, electrical, control, and instrumentation faults</strong>.</li><li>Maintain environmental conditions for <strong>analyzer shelters, control rooms, ICSS rooms, equipment rooms, and other critical areas</strong>.</li><li>Check and maintain <strong>thermostats, sensors, controllers, contactors, relays, motors, and control panels</strong>.</li><li>Perform <strong>filter cleaning/replacement, coil cleaning, refrigerant checks, leak detection, and system servicing</strong>.</li><li>Support <strong>refrigerant recovery, charging, and handling</strong> in accordance with approved procedures and safety requirements.</li><li>Identify abnormal conditions, recurring failures, and equipment deterioration; perform <strong>basic troubleshooting and root-cause assessment</strong> and escalate major defects.</li><li>Verify HVAC performance after maintenance and ensure <strong>environmental conditions are restored before return to service</strong>.</li><li>Maintain accurate <strong>maintenance records, operating logs, checklists, work orders, and CMMS documentation</strong>.</li><li>Coordinate with <strong>Instrumentation, Electrical, ICSS, Analyzer, Operations, and Maintenance teams</strong> for equipment interfaces and shutdown activities.</li><li>Maintain HVAC tools, test equipment, spare parts, and consumables in <strong>safe and serviceable condition</strong>.</li><li>Follow <strong>PTW, LOTO, refrigerant safety, electrical safety, HSE, and procedures</strong>.</li></ul> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p>Wood is recruiting for a Senior Commissioning Engineer to join its Iraq business unit focusing on supporting the Commissioning &amp; Start-Up Manager, drive contractors across all disciplines and accelerate activities in fast-track mode, with no compromise on safety or quality.</p><br><p>This role is a full-time on-site role in Basra, Iraq with travel requirement.<br><strong>Reports to: </strong>Commissioning &amp; Start-Up Manager&nbsp;<br> &nbsp;</p><br><br> Wood is a global leader in consulting, engineering and operations for the energy and materials sectors. With 33,000 people in around 50 countries, Wood supports clients across the full asset lifecycle, delivering safe, predictable outcomes while enabling resilient operations and a lower carbon future. Wood forms the Energy &amp; Materials pillar of Sidara - a global partnership uniting leading multidisciplinary engineering, design, and project management companies. www.woodgroup.com<br> <b>Diversity Statement&nbsp;</b><br> We are an equal opportunity employer that recognises the value of a diverse workforce. All suitably qualified applicants will receive consideration for employment on the basis of objective criteria and without regard to the following (which is a non-exhaustive list): race, colour, age, religion, gender, national origin, disability, sexual orientation, gender identity, protected veteran status, or other characteristics in accordance with the relevant governing laws.<br><br>Responsibilities:<br><p>Wood is recruiting for a Senior Commissioning Engineer to join its Iraq business unit focusing on supporting the Commissioning &amp; Start-Up Manager, drive contractors across all disciplines and accelerate activities in fast-track mode, with no compromise on safety or quality.</p><br><p>This role is a full-time on-site role in Basra, Iraq with travel requirement.<br><strong>Reports to: </strong>Commissioning &amp; Start-Up Manager&nbsp;</p><br><p><i><strong>#Wood #Iraq #Basra #Senior Commissioning Engineer&nbsp;</strong></i></p><br><p><strong><u>The role</u></strong></p><br><p>This is an exciting opportunity for an experienced&nbsp;Senior Commissioning Engineer&nbsp;to join our Iraq Business Unit.</p><br><p><strong>Our Clients and Projects&nbsp;</strong></p><br><p><strong>Designing the future. Transforming the world.&nbsp;</strong></p><br><p>This Project aims to take over the existing asset and maximize the production in 2 phases. This is a fast-track project and schedule-oriented Design to enhance the production.&nbsp;</p><br><p>The Phase 1 will restore, upgrade, and develop the current plant (CPF1) including: Restoration of initial CPF1 capacity; building a new export pipeline (24”, ~30km); restoration of CPF1 integrity and operability; flaring elimination and released water; development of new flowlines, pads, and electrification network for approximately 30 new wells; debottlenecking of the plant; upgrade of the Safety and Security facilities.&nbsp;</p><br><p>Our scope is to provide Engineering, Procurement services and Construction assistance (EPsCa) for the initial development phase of the field in Southern Iraq. The scope of services includes FEED, detailed design, procurement support, and construction and commissioning assistance.</p><br><p><strong><u>What we can offer</u></strong></p><br><ul> <li><strong>Meaningful and interesting projects</strong> Delivered to high profile clients and complex projects in Iraq&nbsp;</li> <li><strong>Commitment to Diversity and Inclusion</strong>; we are an organisation actively committed to diversity and inclusion across our business with employee networks committed to giving all employees a voice&nbsp;</li> <li><strong>Competitive salary</strong> with regular salary reviews to ensure we are rewarding at the right level in line with the market&nbsp;</li> <li><strong>Medical Insurance:&nbsp;</strong>Ensures inpatient and outpatient medical care is available should you require treatment.&nbsp;</li> <li><strong>Commitment to continued professional development;</strong> development plans that are tailored to your individual needs and interests&nbsp;</li> <li><strong>Global connections</strong>: join experts around the world who are at the leading edge of our industry, shaping the standards of our profession&nbsp;</li> <li><strong>Long Service Award:&nbsp;</strong>Wood values the commitment and loyalty of our people. Celebrating Long Service provides an opportunity for the business to demonstrate their appreciation of the hard work, dedication and many years’ services of our employees at 5-year service milestones&nbsp;</li></ul><p><strong><u>Job Objectives/Project context:</u></strong></p><br><p>The project is a gas plant located in Iraq, delivered under a DBOOM (Design, Build, Own, Operate, Maintain) contract. The Construction phase and Mechanical Completion are ongoing, Commissioning to be started very sooner. An experienced reinforcement is required to support the Commissioning &amp; Start-Up Manager, drive contractors across all disciplines and accelerate activities in fast-track mode, with no compromise on safety or quality.</p><br><p><strong>Key Responsibilities:</strong></p><br><ul> <li><strong>Monitoring &amp; driving</strong>: Ensure day-to-day monitoring of contractors’ progress across all disciplines (ICSS, mechanical, electrical, instrumentation, HVAC, utilities…).</li> <li><strong>Acceleration</strong>: Challenge contractors, identify bottlenecks, enforce priorities and push teams to meet commissioning milestones.</li> <li><strong>Methodology</strong>: ORBIT methodology is considered for this project for the follow up of (subsystems, ITR, punch lists, MC/RFCC, completion dossiers).&nbsp;</li> <li><strong>Documentation</strong>: To make sure of the readiness of procedure and dossier to be ready for the activities. Review and validate commissioning procedures, JSA, energization dossiers, LoTo, PSSR…And to prepare all the handover of the phase Precom - Commissioning.</li> <li><strong>Coordination</strong>: Coordinate Mechanical Completion, pre-commissioning, commissioning and start-up activities while securing interfaces and SIMOPS.</li> <li><strong>Reporting</strong>: Run daily and weekly review meetings with Construction, CSU and Company Representative.</li> <li><strong>Handover</strong>: Deliver the closure of punch lists (A/B), remarks clearance and handover to operations.<br> &nbsp;</li></ul><br>Qualifications:<br><p><strong>What makes you remarkable?&nbsp;</strong></p><br><p>At Wood, we are committed to equal opportunities and welcome all talented individuals to consider joining our team. So even if you don't match every statement below but feel you have some of the experience, knowledge or skills needed for this role, we encourage you to apply. It will take all of us working together to deliver solutions to the world’s most critical challenges.&nbsp;&nbsp;</p><br><p><strong>Expected:</strong></p><br><ul> <li>Engineering degree (MSc / BSc) in chemical, mechanical, electrical, instrumentation engineering or equivalent.</li></ul><p><strong>Experience:</strong></p><br><ul> <li><strong>Experience</strong>: Minimum 15 years of experience in commissioning and start-up of Oil &amp; Gas / LNG / petrochemical facilities.</li> <li><strong>Projects</strong>: Proven track record on at least two (2) gas plant, LNG or refinery projects delivered in fast-track mode.</li> <li><strong>Methodology</strong>: knowledge of OPERCOM and Orbit is a plus.</li> <li><strong>Environment</strong>: Previous experience working for a major international operator and managing multi-discipline contractors.</li></ul><p><strong>Technical Skills:</strong></p><br><ul> <li>In-depth knowledge of subsystems, ITR, MC, RFCC, punch lists and system completion.</li> <li>Full command of HSE, ATEX, PtW, LoTo, safety inhibition and PSSR procedures.</li> <li>Strong understanding of process equipment, rotating, HV/LV electrical, F&amp;G, ESD/PSD and ICSS systems.</li> <li>Proficiency with completion management tools (ICAPS or equivalent).</li></ul><p><strong>Personal Qualities:</strong></p><br><ul> <li><strong>Leadership</strong>: Ability to challenge contractors and enforce priorities.</li> <li><strong>Adaptability:</strong> Comfort in fast-track, multicultural and high-pressure environments.</li> <li><strong>Rigor</strong>: Strong reporting discipline, documentation rigor and clear communication.</li> <li><strong>Diplomacy</strong>: Team spirit and diplomacy at Company / EPC / Vendor interfaces.</li></ul><p><strong>Languages:</strong></p><br><ul> <li>Fluent professional English (mandatory).</li> <li>French appreciated. Arabic is a plus.</li></ul><p><strong>Conditions:</strong></p><br><ul> <li>Site-based assignment in Iraq, Rotational.</li></ul> </div>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Site Construction Superintendent (Oil, Gas &amp; Water)<br><br><br><p><b>Job Description</b>: Superintendent Oil &amp; Gas &amp; Water Projects&nbsp;</p><br><br><p><b>Company</b>: KBR Iraq</p><br><br><p><b>Location:&nbsp;</b>Majnoon Oil Field, Iraq Rotation 28/28</p><br><br><p><b>Nationality:</b>&nbsp;Any</p><br><br><br><p>The Superintendent is responsible for leading, coordinating, and supervising all site construction activities across Oil &amp; Gas and water infrastructure projects within the Majnoon Oil Field. This role ensures safe execution, compliance with project specifications, alignment with KBR standards, and delivery of work packages on schedule. The Superintendent acts as the primary interface between field crews, subcontractors, and project management, ensuring operational discipline and high-quality workmanship.</p><br><br><br><p><b>Accountability / Expectations</b></p><br><br><ul><li>Direct and supervise daily construction activities for oil &amp; gas facilities, pipelines, water treatment systems, and associated civil works.</li><li>Manage multi‑disciplinary site teams including civil, mechanical, piping, electrical, and water project crews.</li><li>Coordinate work fronts, manpower allocation, equipment usage, and material availability to maintain progress.</li><li>Ensure all work is executed in accordance with IFC drawings, project specifications, and KBR procedures.</li><li>Enforce KBR HSSE policies and site safety rules, lead by example in promoting a strong safety culture.</li><li>Conduct site inspections, and hazard identification activities.</li><li>Ensure all permits to work (PTW) are properly issued, controlled, and closed.</li><li>Support incident investigations and implement corrective actions.</li><li>Monitor construction quality and ensure compliance with project standards and client requirements.</li><li>Review and interpret drawings, method statements, and technical documents.</li><li>Raise and resolve technical queries (TQs) with engineering teams when required.</li><li>Ensure proper documentation of inspections, test records, and completion certificates.</li><li>Track daily progress, productivity, and resource utilization; report deviations promptly.</li><li>Prepare daily/weekly site reports, progress updates, and look‑ahead plans.</li><li>Coordinate with planning and project controls to maintain accurate schedules and forecasts.</li><li>Oversee subcontractor performance, ensuring adherence to scope, quality, and safety requirements.</li><li>Validate subcontractor work completion for invoicing and progress measurement.</li><li>Resolve site-level conflicts and interface issues between contractors and disciplines.</li><li>Ensure timely availability of materials, tools, and equipment at work fronts.</li><li>Coordinate with warehouse, procurement, and logistics teams for site needs.</li><li>Supervise construction of water treatment units, pumping stations, pipelines, and utility networks.</li><li>Ensure compliance with water project standards, environmental requirements, and testing protocols.</li><li>Oversee hydrotesting, flushing, commissioning support, and handover documentation.</li></ul><br><p><b>Education</b></p><br><br><p>Bachelor’s degree or diploma in Engineering (Civil, Mechanical, or related field).</p><br><br><br><p><b>Experience</b></p><br><br><p>10+ years experience in Oil &amp; Gas construction, experience in water infrastructure projects.</p><br><br><br><ul><li>Strong knowledge of HSSE systems, PTW, SIMOPS, and field execution in live oilfield environments.</li><li>Proven leadership experience managing large site teams and subcontractors.</li><li>Ability to read and interpret engineering drawings and technical documents.</li></ul><br><br><br> </div>

<p><h4>Job description</h4> <p>The computer systems analyst I provides several phases of the required systems analysis where the nature of the system is predetermined, uses established fact-finding approaches, knowledge of pertinent work processes and procedures, and familiarity with related computer programming practices, system software, and computer equipment.</p> <p>This analyst provides several phases of the required systems analysis where the nature of the system is predetermined, uses established fact-finding approaches, knowledge of pertinent work processes and procedures, and familiarity with related computer programming practices, system software, and computer equipment.</p> <p>Carries out fact finding and analyses as assigned, usually of a single activity or a routine problem, and applies established procedures where the nature of the system, feasibility, computer equipment, and programming language have already been decided.</p> <p>May assist a higher-level systems analyst by preparing the detailed specifications required by computer programmers from information developed by the higher-level analyst.</p> <p>May research routine user problems and solve them by modifying the existing system when the solutions follow clear precedents.</p> <p>Prepare cost and deadline estimates as required for review.</p> <p>Works independently to adapt guides to specific situations; resolve problems and deviations according to established practices; and obtain advice where precedents are unclear or not available.</p> <p>Carries out objectives, priorities, and deadlines as defined by the supervisor.</p> <p>May supervise technician and others who assist in specific assignments.</p> <p>Will have some variation within and across contracts and may list additional or specific job duties related to assigned function/level which are not aforementioned.</p> <h4>Minimum requirements</h4> <p>High school diploma or equivalent is required. Certification of education level is required.</p> <p>CompTIA Security+ certification.</p> <p>Must possess two (2) years of related experience in computer systems analysis.</p> <p>Ability to obtain and maintain a US government SECRET clearance is required (prefer active Secret clearance). US citizenship is required for SECRET clearance at this work location.</p> <p>A valid U.S. passport is required to travel internationally. Passport must have a minimum of 6 blank pages and 2 plus year validity on expiration date of passport.</p> <p>Must be able to pass CENTCOM medical requirements for deployment.</p> <p>Must be able to obtain a visa in CENTCOM locations.</p> <h4>Knowledge & skills</h4> <ul> <li>Requires competence in most phases of system analysis.</li> <li>Systems analysis and design skills in an area such as a record keeping or scientific operation.</li> <li>Knowledge of pertinent system software and computer equipment.</li> <li>Knowledge of work processes, applicable regulations, and practices of the assigned subject-matter area.</li> <li>Ability to recognize probable interactions of related computer systems and predict impact of a change in assigned system.</li> <li>Good problem-solving skills.</li> <li>Self-motivated and the ability to work independently.</li> </ul> <h4>Physical requirements/working environment</h4> <ul> <li>Must be able to walk and stand on level and/or inclined surfaces for extended periods throughout the day.</li> <li>Must be able to lift/push/pull minimum of 50 pounds.</li> <li>May work in maintenance shop or outside.</li> <li>Must be able to work in a shop where the environment is drafty, noisy, and dirty.</li> <li>May be exposed to extreme noise from operating equipment.</li> <li>May be exposed to electrical shock hazards or work near moving mechanical parts or vehicles.</li> <li>May be expected to work in austere environments and all weather conditions.</li> </ul></p><p></p>

<p><h4>Electrical technician</h4> <p>Responsible for study, design, specification and services related to electrical and electronic systems including power generation, transmission and distribution, power systems performance and control, cabling and wiring, lighting, motor control centers, communications systems, cathodic protection, grounding lightning protection, heat tracing, etc.</p> <p>Under direct supervision, evaluates, selects, and applies standard engineering techniques, procedures, and criteria, using judgment in making minor adaptations and modifications. With additional experience within one functional area, assists in the design of larger and more complex assignments which involve conventional types of plans, investigations and surveys with relatively few complex features for which there are precedents.</p> <p>Job tasks, correctly performed, impact indirectly on cost containment, efficiency, profitability or operations. Skills are typically acquired through an undergraduate degree in engineering and minimum of 2 years related experience, with typical experience ranging from 3-7 years.</p> <p>Assignments are generally well defined with clearly specified objectives. Assignments usually include one or more of the following:</p> <ul> <li>Design and development</li> <li>Testing of materials</li> <li>Preparation or checking of design calculations and specifications</li> <li>Studies</li> <li>Research investigations</li> <li>Report preparation</li> <li>Other activities of limited scope</li> </ul> <p>Certification as an engineer-in-training is preferred.</p></p><p></p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Electrical Technician<br><br><p>Responsible for study, design, specification and services related to electrical and electronic systems including power generation, transmission and distribution, power systems performance and control, cabling and wiring, lighting, motor control centers, communications systems, cathodic protection, grounding lightning protection, heat tracing etc. Under direct supervision, evaluates, selects, and applies standard engineering techniques, procedures, and criteria, using judgment in making minor adaptations and modifications. With additional experience within one functional area, assists in the design of larger and more complex assignments which involve conventional types of plans, investigations and surveys with relatively few complex features for which there are precedents. Job tasks, correctly performed, impact indirectly on cost containment, efficiency, profitability or operations. Skills are typically acquired through an undergraduate degree in Engineering and minimum of 2 years related experience, with typical experience ranging from 3-7 years. Assignments are generally well defined with clearly specified objectives. Assignments usually include one or more of the following: design and development, testing of materials, preparation or checking of design calculations and specifications, studies, research investigations, report preparation, and other activities of limited scope. Certification as an Engineer-In-Training is preferred.</p><br><br><br><br><br> </div>

<p>The Mechanical &amp; Rotating QC Inspector is responsible for monitoring, supervising, and controlling all Quality Control activities related to mechanical static and rotating equipment within the AGUP2 Project CPF2 Package. He ensures that all contractual, technical, and quality requirements are properly implemented by the Contractor and Subcontractors during Construction, Pre-commissioning, and Commissioning phases. The position reports directly to the CPF2 Site QC Superintendent and works closely with Construction, Commissioning, QC disciplines, Vendors, and Contractor/Subcontractor teams .</p><p><strong>MAIN MISSIONS/RESPONSIBILITIES</strong></p><p><strong>Daily Inspection &amp; Reporting</strong></p><ul><li>Monitor and record all rotating equipment activities on a daily basis.</li><li>Conduct routine inspections in construction areas, equipment installation zones, and pre-commissioning areas.</li><li>Perform specific inspections on rotating machinery and associated installation activities.</li><li>Provide daily update and weekly reporting directly to the CPF2 Site QC Superintendent, covering:</li><ul><li>Inspection progress and key findings</li><li>Non-conformities and recurring defects</li><li>Critical issues requiring escalation or arbitration</li><li>Status of corrective actions</li><li>Quality trends and contractor performance indicators</li></ul><li>Contribute actively to daily/weekly QC coordination meetings and ensure the QC Superintendent receives all relevant data for consolidated site reporting.</li><li>Maintain up-to-date records, ITP follow-up, NCR/CAR tracking, and Mechanical Completion documentation enabling full visibility for the QC Superintendent.</li></ul><p><strong>Rotating Equipment Installation &amp; Inspection</strong></p><ul><li>Inspect rotating equipment such as: Pumps (centrifugal, reciprocating, screw), Compressors (reciprocating, centrifugal), Turbines, Electric motors, Blowers and fans</li><li>Verify foundations, grout, anchor bolts, leveling, and mounting conditions for rotating equipment.</li><li>Check alignment (cold/hot), coupling installation, run-out, and shaft rotation.</li><li>Verify lubrication systems, mechanical seals, and auxiliary systems.</li><li>Review and validate inspection reports, punch lists, and test results (vibration, performance, run-in).</li><li>Ensure compliance with vendor documentation, project specifications, and industry standards.</li></ul><p><strong>Pre-Commissioning &amp; Commissioning</strong></p><ul><li>Witness and verify rotating equipment pre-commissioning activities: Oil flushing, Lubrication system checks, Motor solo-run, Direction of rotation, Alignment verification</li><li>Participate in commissioning tests: Vibration analysis, Performance testing, Functional checks</li><li>Ensure all rotating equipment is ready for handover to Commissioning.</li></ul><p><strong>Documentation &amp; Compliance</strong></p><ul><li>Review and comment on Contractors' and Suppliers' ITPs, Method Statements, and procedures.</li><li>Ensure proper implementation of approved drawings, QC plans, surveillance plans, and ITPs.</li><li>Verify vendor documentation, equipment certification files, and material certificates.</li><li>Issue Quality Records, NCRs, and CARs when required.</li><li>Ensure proper traceability of inspections, tests, and mechanical completion documentation.</li></ul><p><strong>Welding, NDT &amp; Interfaces (Only where rotating equipment interfaces with piping or structural supports)</strong></p><ul><li>Coordinate with QC Welding, NDT, Piping, and Structural teams for interface inspections.</li><li>Verify NDT results related to rotating equipment supports, baseplates, and connected piping.</li><li>Ensure correct implementation of flange alignment and piping connection tolerances.</li></ul><p><strong>Non-Conformities &amp; Corrective Actions</strong></p><ul><li>Identify and report non-conformities or deviations in a timely manner.</li><li>Ensure corrective actions are implemented and verified.</li><li>Immediately escalate critical anomalies to the QC Superintendent.</li></ul><p><strong>Coordination &amp; Interface</strong></p><ul><li>Participate in daily/weekly construction and QC coordination meetings.</li><li>Interface with Construction, Commissioning, Engineering, Vendors, and Contractor QC teams.</li><li>Support technical clarifications and design queries with Engineering when required.</li><li>Participate in audits (Construction, HSE, QC) and site visits.</li><li>Ensure confidentiality of all documentation under responsibility.</li></ul><p><strong>Scope of Work</strong></p><p><strong>Rotating Equipment</strong></p><p>The Mechanical &amp; Rotating QC Inspector covers the following equipment categories:</p><ul><li><strong>Rotating Equipment</strong><ul><li>Centrifugal pumps</li><li>Reciprocating pumps</li><li>Screw pumps</li><li>Centrifugal compressors</li><li>Reciprocating compressors</li><li>Gas/steam turbines</li><li>Electric motors</li><li>Blowers and fans</li><li>Mechanical packages containing rotating components</li></ul></li><li><strong>Associated Systems</strong><ul><li>Alignment systems (laser, dial indicator)</li><li>Lubrication systems</li><li>Mechanical seals</li><li>Couplings</li><li>Vibration monitoring systems</li><li>Auxiliary systems (cooling, sealing, lubrication)</li></ul></li></ul><p><strong>Desired Candidate Profile</strong></p><p>Professional Experience Minimum 10 years of experience in Mechanical &amp; Rotating QC on major Oil &amp; Gas EPC projects. Strong experience with rotating equipment installation, alignment, and commissioning. Experience on CPF, refinery, or large industrial facilities is strongly preferred. Demonstrated ability in resource planning, decision-making, and team coordination.</p><p>Technical Competencies Solid knowledge of rotating equipment ( pumps, compressors, turbines, motors, fans ). Strong understanding of mechanical installation requirements ( alignment, foundations, couplings ). Ability to interpret standards, codes, specifications, and technical drawings. Proficiency with measuring instruments ( micrometers, calipers, dial indicators, laser alignment tools ). Knowledge of vibration analysis and performance testing. Understanding of NCR, deviation, and concession processes. Familiarity with digital QC systems ( Aconex, SharePoint, SmartPlant, or equivalent ) is a plus.</p><p>Behavioral Competencies Exemplary behavior regarding Company Code of Conduct and HSSE rules. Ensure that all HSSE training are completed and HSE rules implemented within his area of responsibility. Ability to represent the Company in discussions and meetings with Vendors, Contractors, and Subcontractors. High attention to detail and strong reporting discipline. Ability to work autonomously in a harsh, remote site environment. Leadership, team spirit, and resilience under pressure. Ability to transfer knowledge to team members. Fluent English (mandatory).</p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><strong>About the company:</strong></p><br><br><p><strong>iMaker Group</strong>is a renowned for its expertise in luxury villas, hospitality, and commercial developments. We are a dynamic consortium of companies offering comprehensive services in master planning, architecture, interior design, construction, project management, and the sourcing of furniture and materials. With operations spanning<strong>Dubai, London, Riyadh, Miami and Cairo. </strong>iMaker Group delivers diverse projects on a global scale.<br></p><br><br><p><strong>Summary of the role:</strong></p><br><br><p>The Project Manager will be responsible for overseeing finishing tasks in construction projects, including coordinating with design teams, managing budgets, sourcing and inspecting materials, and ensuring compliance with project specifications. It requires liaising between contractors, suppliers, and owners, monitoring the implementation of key construction phases, and ensuring quality across interior and exterior works.</p><br><br><br><p><strong>Key responsibilities:</strong></p><br><br><ul><li>Collaborate with the team to understand design specs and create detailed finishing schedules.</li><li>Assist in developing and managing the finishing budget, tracking expenses and variances.</li><li>Source, procure, and inspect materials for quality and compliance with project requirements.</li><li>Coordinate with contractors and owners, securing material samples and reviewing offers.</li><li>Act as a liaison between design teams, subcontractors, and suppliers; provide regular updates.</li><li>Oversee project implementation, including contractor offers, scheduling, planning, and material approval. Review and approve shop drawings and supervise key construction works (excavation, carpentry, concrete, insulation, etc.), ensuring quality and compliance with engineering drawings.</li><li>Oversee all finishing tasks, including exterior and interior works (facades, plastering, painting, woodwork, electrical, plumbing, HVAC, landscaping, pool, etc.) to ensure it meets design specifications and industry standards.</li><li>Verify executed quantities and coordinate overlapping works.</li><li>Enforce safety protocols and ensure compliance with local building codes and regulations.</li><li>Identify and resolve issues in finishing work, proposing solutions to improve efficiency.</li><li>Maintain accurate records of progress, inspections, and change orders; generate required reports.</li><li>Supervise and guide subcontractors and laborers, fostering a productive work environment.</li><li>Draft and audit contracts, review schedules, and ensure timely work completion.</li><li>Manage work receipt with proper documentation and owner approval.</li><li>Submit daily and weekly progress reports to Line Manager.</li><li>Perform other duties as assigned by Management.</li><li>Stay informed on the latest trends, materials and technology in the design industry to keep our projects at the forefront of innovation.<br></li></ul><p><strong>Education and Experience:</strong></p><br><br><ul><li>Bachelor's degree in Architecture, Construction Management, or Civil Engineering field.</li><li>Project Management Professional (PMP) or equivalent is preferable.</li><li>12+ years of professional experience in Project Management with a focus on high-end projects working on budgets, procurement, and coordinating with contractors and design teams.</li></ul><br><p><strong>Knowledge, Skills and Abilities:</strong></p><br><br><ul><li>Proficient in using AutoCAD, SketchUp, and Project management software.</li><li>Arabic speaking is a must.</li><li>Strong project management, organizational, and budgeting skills.</li><li>Proven track record of delivering interior and exterior projects.</li><li>Strong leadership and team coordination abilities.</li><li>Excellent client-facing communication skills.</li><li>Creative and strategic mindset with ability to think innovatively and execute complete design concepts.</li><li>Proactive in identifying and resolving project issues.</li><li>Strong organizational and multitasking abilities, with a high attention to detail.</li></ul><br><p><strong>Working conditions and Environment:</strong></p><br><br><ul><li>The position is site based in Baghdad, Iraq.</li><li>The position may have occasional international travel requirements.</li></ul><br><p><strong>Success Metrics &amp; KPIs:</strong></p><br><br><br><ul><li><strong>Client Satisfaction score after handover:</strong> Client feedback score after milestones/handover.</li><li><strong>Weekly progress reporting:</strong> Timely submission of accurate weekly site reports.</li><li><strong>Budget and material control:</strong> Actual project cost vs. approved budget.</li><li><strong>Project completion on schedule: </strong>% of project milestones achieved on or before planned dates.</li><li><strong>Subcontractor performance management: </strong>Evaluate subcontractors based on quality, timeline, and coordination.</li><li><strong>Problem-solving &amp; escalation:</strong> Timely identification and resolution of site issues.<br></li></ul><p><strong>What We Offer?</strong></p><br><br><ul><li>Opportunities to work on high-profile, international projects.</li><li>A chance to work in a collaborative, creative work environment that fosters innovation.</li><li>Opportunities for career growth and professional development.</li><li>Competitive salary and benefits package.<br></li></ul><p><i>We are an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex (including pregnancy), sexual orientation, gender identity, national origin, age, or disability.</i><br></p><br><br><p><i>By submitting your application, you consent to iMaker Group processing your personal data in compliance with applicable data protection laws, while ensuring strict confidentiality.</i></p><br><br><br> <br><br> </div>

<p><h4>Job description</h4> <p>The computer systems analyst I provides several phases of the required systems analysis where the nature of the system is predetermined, uses established fact-finding approaches, knowledge of pertinent work processes and procedures, and familiarity with related computer programming practices, system software, and computer equipment.</p> <p>This analyst provides several phases of the required systems analysis where the nature of the system is predetermined, uses established fact-finding approaches, knowledge of pertinent work processes and procedures, and familiarity with related computer programming practices, system software, and computer equipment.</p> <p>Carries out fact finding and analyses as assigned, usually of a single activity or a routine problem, and applies established procedures where the nature of the system, feasibility, computer equipment, and programming language have already been decided.</p> <p>May assist a higher-level systems analyst by preparing the detailed specifications required by computer programmers from information developed by the higher-level analyst.</p> <p>May research routine user problems and solve them by modifying the existing system when the solutions follow clear precedents.</p> <p>Prepare cost and deadline estimates as required for review.</p> <p>Works independently to adapt guides to specific situations; resolve problems and deviations according to established practices; and obtain advice where precedents are unclear or not available.</p> <p>Carries out objectives, priorities, and deadlines as defined by the supervisor.</p> <p>May supervise technician and others who assist in specific assignments.</p> <p>Will have some variation within and across contracts and may list additional or specific job duties related to assigned function/level which are not aforementioned.</p> <h4>Minimum requirements</h4> <p>High school diploma or equivalent is required. Certification of education level is required.</p> <p>CompTIA Security+ certification.</p> <p>Must possess two (2) years of related experience in computer systems analysis.</p> <p>Ability to obtain and maintain a US government SECRET clearance is required (prefer active Secret clearance). US citizenship is required for SECRET clearance at this work location.</p> <p>A valid U.S. passport is required to travel internationally. Passport must have a minimum of 6 blank pages and 2 plus year validity on expiration date of passport.</p> <p>Must be able to pass CENTCOM medical requirements for deployment.</p> <p>Must be able to obtain a visa in CENTCOM locations.</p> <h4>Knowledge & skills</h4> <ul> <li>Requires competence in most phases of system analysis.</li> <li>Systems analysis and design skills in an area such as a record keeping or scientific operation.</li> <li>Knowledge of pertinent system software and computer equipment.</li> <li>Knowledge of work processes, applicable regulations, and practices of the assigned subject-matter area.</li> <li>Ability to recognize probable interactions of related computer systems and predict impact of a change in assigned system.</li> <li>Good problem-solving skills.</li> <li>Self-motivated and the ability to work independently.</li> </ul> <h4>Physical requirements/working environment</h4> <ul> <li>Must be able to walk and stand on level and/or inclined surfaces for extended periods throughout the day.</li> <li>Must be able to lift/push/pull minimum of 50 pounds.</li> <li>May work in maintenance shop or outside.</li> <li>Must be able to work in a shop where the environment is drafty, noisy, and dirty.</li> <li>May be exposed to extreme noise from operating equipment.</li> <li>May be exposed to electrical shock hazards or work near moving mechanical parts or vehicles.</li> <li>May be expected to work in austere environments and all weather conditions.</li> </ul></p><p></p>

<p>O &amp; M technician for daily job orders and team follow-up Daily task O&amp;M follow-up Network performances and KPI with outage follow-up Project implementations participations Daily reporting.</p><p>Technical knowledge (Power, Generators and cooling) maintenances and repair Preventive and correction process</p><p>Behavioral Competencies: Delivering Results &amp; Fostering Ownership. Building Customer Value.</p><p>Technical Competencies: Access Network Operations Network Monitoring Passive Network Operations Problem Solving Technical Writing and Reporting</p><p><strong>Desired Candidate Profile</strong></p><p>Mechanical /Electrical perp industry / technology institute 5-year experiences in field</p>

<p><h4>Belong, connect, grow, with KBR!</h4> <p>The KBR team of teams delivers future-forward science, technology and engineering solutions and mission-critical services that help governments and companies around the world accomplish their most important objectives, while also helping achieve their sustainability goals.</p> <p>KBR Sustainable Technology Solutions provides holistic and value-added solutions across the entire asset life cycle. These include world-class licensed process technologies, differentiated advisory services, deep technical domain expertise, energy transition solutions, high-end design and engineering capabilities, and smart solutions to optimize planned and operating assets.</p> <p>KBR is looking for a Site Electrical Supervisor to be based in Basra, Iraq – daily commute.</p> <h4>Main missions</h4> <ul> <li>Ensure safe, compliant, and high-quality execution of all electrical construction, installation, testing, and pre-commissioning activities at site.</li> <li>Supervise EPC contractor and subcontractors electrical works in accordance with approved drawings, project specifications, method statements, ITPs, applicable codes, and company requirements.</li> <li>Coordinate electrical activities with construction, engineering, QA/QC, HSE, commissioning, and other disciplines to achieve the project schedule and system priorities.</li> <li>Identify technical, quality, safety, and constructability issues, and ensure timely resolution and close-out.</li> <li>Support mechanical completion, energization readiness, commissioning, and handover of electrical systems.</li> </ul> <h4>Key activities</h4> <p><strong>Site supervision and construction control</strong></p> <ul> <li>Supervise daily electrical construction activities, including installation of HV, MV, and LV equipment and systems.</li> <li>Monitor installation of transformers, switchgear, motor control centres, generators, UPS and DC systems, distribution boards, power and control cables, lighting, small power, earthing, lightning protection, and electrical heat tracing where applicable.</li> <li>Verify equipment location, orientation, access, supports, interfaces, and installation against approved AFC drawings and vendor requirements.</li> <li>Ensure cable tray, ladder, conduit, cable pulling, segregation, dressing, glanding, termination, identification, and fire-stopping works comply with project requirements.</li> <li>Monitor preservation, storage, handling, and protection of electrical equipment and materials at site.</li> <li>Ensure work fronts are properly planned and that required drawings, materials, tools, access, permits, and preceding works are available.</li> </ul> <p><strong>Technical compliance and quality</strong></p> <ul> <li>Ensure execution in accordance with approved AFC drawings, specifications, equipment data sheets, vendor documentation, method statements, ITPs, and applicable international standards.</li> <li>Participate in inspection requests and witness required hold and witness points with QA/QC personnel.</li> <li>Inspect equipment installation, bolted connections, cable routing and segregation, terminations, earthing connections, labelling, and general workmanship.</li> <li>Witness or review electrical tests, as applicable, including insulation resistance, continuity, earthing resistance, winding resistance, ratio tests, protection relay tests, cable tests, functional checks, and interlock verification.</li> <li>Review and follow up punch items, site observations, non-conformities, and corrective actions until closure.</li> <li>Assist in checking red-line mark-ups, test records, inspection reports, and as-built documentation.</li> </ul> <p><strong>Contractor supervision and progress</strong></p> <ul> <li>Monitor contractor and subcontractor manpower, supervision, productivity, work quality, and compliance with the approved construction schedule.</li> <li>Review short-term work plans and report constraints, delays, interface issues, and recovery requirements to the Electrical Superintendent or Construction Manager.</li> <li>Attend daily coordination meetings, site walkthroughs, progress reviews, toolbox talks, and technical meetings as required.</li> <li>Prepare clear daily and weekly reports covering progress, manpower, inspections, constraints, quality issues, HSE observations, and planned activities.</li> <li>Ensure contractor personnel assigned to specialized electrical work are competent and appropriately authorized.</li> </ul> <p><strong>Interfaces, completion and commissioning</strong></p> <ul> <li>Coordinate electrical interfaces with civil, structural, mechanical, piping, instrumentation, telecom, HVAC, package vendors, and commissioning teams.</li> <li>Ensure foundations, embedded items, sleeves, trenches, rooms, supports, cable routes, and equipment access are ready before electrical installation.</li> <li>Support systemization, mechanical completion checks, punch-listing, turnover dossier preparation, and handover by system or subsystem.</li> <li>Participate in energization readiness reviews and ensure outstanding construction, quality, and safety items are controlled before energization.</li> <li>Support pre-commissioning and commissioning activities, including vendor attendance, functional testing, loop and interlock checks, and troubleshooting.</li> </ul> <h4>HSE responsibility</h4> <ul> <li>Ensure electrical works are performed in accordance with project HSE requirements, approved risk assessments, method statements, permit-to-work procedures, and isolation rules.</li> <li>Pay particular attention to electrical safety, lockout/tagout, temporary power, excavation and underground services, lifting operations, work at height, confined spaces, and simultaneous operations.</li> <li>Intervene and stop unsafe work when necessary, report unsafe acts and conditions, and verify implementation of corrective measures.</li> <li>Participate in toolbox talks, safety walks, audits, incident investigations, and lessons-learned activities.</li> <li>Promote a strong safety culture and ensure good housekeeping in electrical work areas, substations, electrical rooms, and cable routes.</li> </ul> <h4>Professional experience</h4> <ul> <li>More than 10 years of relevant experience in electrical construction and site supervision on large EPC/EPSCC projects in oil and gas, power generation, water treatment, utilities, or major industrial facilities.</li> <li>Significant field experience supervising electrical installation, testing, pre-commissioning, and handover activities.</li> </ul> <h4>Experience in similar position</h4> <ul> <li>Previous experience as Site Electrical Supervisor, Electrical Construction Supervisor, or equivalent position on a major project.</li> <li>Hands-on experience with HV, MV, and LV systems; transformers; switchgear; MCCs; UPS and DC systems; power and control cables; earthing; lighting; and electrical equipment associated with rotating and packaged equipment.</li> <li>Experience in power generation facilities, large pumping stations, substations, or water treatment plants is preferred.</li> <li>Experience on Middle East projects and/or remote construction sites is an advantage.</li> </ul> <h4>Technical skills</h4> <ul> <li>Strong knowledge of electrical construction methods, installation practices, inspection requirements, testing, energization, and completion processes.</li> <li>Ability to read and interpret single-line diagrams, schematics, wiring diagrams, cable schedules, equipment layouts, earthing layouts, interconnection diagrams, vendor drawings, and AFC documentation.</li> <li>Good understanding of electrical interfaces with civil, mechanical, instrumentation, telecom, HVAC, and package systems.</li> <li>Familiarity with ITP, RFI, NCR, punch-list, mechanical completion, turnover, and quality-record processes.</li> <li>Working knowledge of applicable IEC, IEEE, NFPA, ISO, and project-specific standards and requirements.</li> <li>Competence in reporting, progress monitoring, work-front planning, and use of standard office applications.</li> </ul> <h4>Level / diploma</h4> <ul> <li>Bachelor’s degree in Electrical Engineering preferred.</li> <li>A recognized technical diploma in Electrical Engineering may be accepted with substantial relevant site experience.</li> <li>Relevant electrical safety, HV authorization, commissioning, or construction supervision training is an advantage.</li> </ul> <h4>Languages</h4> <ul> <li>Proficiency in English is mandatory. Knowledge of Arabic is an advantage.</li> </ul> <h4>Soft skills</h4> <ul> <li>Strong field presence, leadership, and contractor-management capability.</li> <li>Clear communication and coordination skills in a multicultural environment.</li> <li>Proactive, practical, safety-conscious, and quality-focused approach.</li> <li>Ability to prioritize work, resolve site issues, manage interfaces, and work under schedule pressure.</li> <li>Ability to challenge non-compliant work and intervene firmly when safety or quality is at risk.</li> </ul> <p>Interested and suitable candidates please apply for the role. Suitable candidates will be contacted directly.</p></p><p></p>

<h2 class="h5">Job description</h2> <div class="t-break" data-jb-field="description"> <p><b>Title:</b></p><br><br>Site Electrical Supervisor<br><br><p><i><b>"Belong, Connect, Grow, with KBR!</b></i></p><br><br><br><p><i><b>The KBR team of teams delivers future-forward science, technology and engineering solutions and mission-critical services that help governments and companies around the world accomplish their most important objectives, while also helping achieve their sustainability goals.</b></i></p><br><br><br><p><i><b>KBR Sustainable Technology Solutions provides holistic and value-added solutions across the entire asset life cycle. These include world-class licensed process technologies, differentiated advisory services, deep technical domain expertise, energy transition solutions, high-end design and engineering capabilities, and smart solutions to optimize planned and operating assets."</b></i></p><br><br><br><p>KBR is looking for a&nbsp;<b>Site Electrical Supervisor </b>to be based in <b>Basra, Iraq – Daily Commute</b></p><br><br><br><p><b><u>MAIN MISSIONS</u></b></p><br><br><ul><li>Ensure safe, compliant, and high-quality execution of all electrical construction, installation, testing, and pre-commissioning activities at site.</li></ul><ul><li>Supervise EPC Contractor and subcontractors electrical works in accordance with approved drawings, project specifications, method statements, ITPs, applicable codes, and COMPANY requirements.</li></ul><ul><li>Coordinate electrical activities with construction, engineering, QA/QC, HSE, commissioning, and other disciplines to achieve the project schedule and system priorities.</li></ul><ul><li>Identify technical, quality, safety, and constructability issues, and ensure timely resolution and close-out.</li></ul><ul><li>Support mechanical completion, energization readiness, commissioning, and handover of electrical systems.</li></ul><br><p><b><u>KEY ACTIVITIES</u></b></p><br><br><p><b>Site Supervision and Construction Control</b></p><br><br><ul><li>Supervise daily electrical construction activities, including installation of HV, MV, and LV equipment and systems.</li></ul><ul><li>Monitor installation of transformers, switchgear, motor control centres, generators, UPS and DC systems, distribution boards, power and control cables, lighting, small power, earthing, lightning protection, and electrical heat tracing where applicable.</li></ul><ul><li>Verify equipment location, orientation, access, supports, interfaces, and installation against approved AFC drawings and vendor requirements.</li></ul><ul><li>Ensure cable tray, ladder, conduit, cable pulling, segregation, dressing, glanding, termination, identification, and fire-stopping works comply with project requirements.</li></ul><ul><li>Monitor preservation, storage, handling, and protection of electrical equipment and materials at site.</li></ul><ul><li>Ensure work fronts are properly planned and that required drawings, materials, tools, access, permits, and preceding works are available.</li></ul><br><p><b>Technical Compliance and Quality</b></p><br><br><ul><li>Ensure execution in accordance with approved AFC drawings, specifications, equipment data sheets, vendor documentation, method statements, ITPs, and applicable international standards.</li></ul><ul><li>Participate in inspection requests and witness required hold and witness points with QA/QC personnel.</li></ul><ul><li>Inspect equipment installation, bolted connections, cable routing and segregation, terminations, earthing connections, labelling, and general workmanship.</li></ul><ul><li>Witness or review electrical tests, as applicable, including insulation resistance, continuity, earthing resistance, winding resistance, ratio tests, protection relay tests, cable tests, functional checks, and interlock verification.</li></ul><ul><li>Review and follow up punch items, site observations, non-conformities, and corrective actions until closure.</li></ul><ul><li>Assist in checking red-line mark-ups, test records, inspection reports, and as-built documentation.</li></ul><br><p><b>Contractor Supervision and Progress</b></p><br><br><ul><li>Monitor contractor and subcontractor manpower, supervision, productivity, work quality, and compliance with the approved construction schedule.</li></ul><ul><li>Review short-term work plans and report constraints, delays, interface issues, and recovery requirements to the Electrical Superintendent or Construction Manager.</li></ul><ul><li>Attend daily coordination meetings, site walkthroughs, progress reviews, toolbox talks, and technical meetings as required.</li></ul><ul><li>Prepare clear daily and weekly reports covering progress, manpower, inspections, constraints, quality issues, HSE observations, and planned activities.</li></ul><ul><li>Ensure contractor personnel assigned to specialized electrical work are competent and appropriately authorized.</li></ul><br><p><b>Interfaces, Completion and Commissioning</b></p><br><br><ul><li>Coordinate electrical interfaces with civil, structural, mechanical, piping, instrumentation, telecom, HVAC, package vendors, and commissioning teams.</li></ul><ul><li>Ensure foundations, embedded items, sleeves, trenches, rooms, supports, cable routes, and equipment access are ready before electrical installation.</li></ul><ul><li>Support systemization, mechanical completion checks, punch-listing, turnover dossier preparation, and handover by system or subsystem.</li></ul><ul><li>Participate in energization readiness reviews and ensure outstanding construction, quality, and safety items are controlled before energization.</li></ul><ul><li>Support pre-commissioning and commissioning activities, including vendor attendance, functional testing, loop and interlock checks, and troubleshooting.</li></ul><br><p><b><u>HSE RESPONSIBILITY</u></b></p><br><br><ul><li>Ensure electrical works are performed in accordance with project HSE requirements, approved risk assessments, method statements, permit-to-work procedures, and isolation rules.</li></ul><ul><li>Pay particular attention to electrical safety, lockout/tagout, temporary power, excavation and underground services, lifting operations, work at height, confined spaces, and simultaneous operations.</li></ul><ul><li>Intervene and stop unsafe work when necessary, report unsafe acts and conditions, and verify implementation of corrective measures.</li></ul><ul><li>Participate in toolbox talks, safety walks, audits, incident investigations, and lessons-learned activities.</li></ul><ul><li>Promote a strong safety culture and ensure good housekeeping in electrical work areas, substations, electrical rooms, and cable routes.</li></ul><br><p><b>Professional Experience</b></p><br><br><ul><li>More than 10 years of relevant experience in electrical construction and site supervision on large EPC/EPSCC projects in oil and gas, power generation, water treatment, utilities, or major industrial facilities.</li></ul><ul><li>Significant field experience supervising electrical installation, testing, pre-commissioning, and handover activities.</li></ul><br><p><b>Experience in Similar Position</b></p><br><br><ul><li>Previous experience as Site Electrical Supervisor, Electrical Construction Supervisor, or equivalent position on a major project.</li></ul><ul><li>Hands-on experience with HV, MV, and LV systems; transformers; switchgear; MCCs; UPS and DC systems; power and control cables; earthing; lighting; and electrical equipment associated with rotating and packaged equipment.</li></ul><ul><li>Experience in power generation facilities, large pumping stations, substations, or water treatment plants is preferred.</li></ul><ul><li>Experience on Middle East projects and/or remote construction sites is an advantage.</li></ul><br><p><b>Technical Skills</b></p><br><br><ul><li>Strong knowledge of electrical construction methods, installation practices, inspection requirements, testing, energization, and completion processes.</li></ul><ul><li>Ability to read and interpret single-line diagrams, schematics, wiring diagrams, cable schedules, equipment layouts, earthing layouts, interconnection diagrams, vendor drawings, and AFC documentation.</li></ul><ul><li>Good understanding of electrical interfaces with civil, mechanical, instrumentation, telecom, HVAC, and package systems.</li></ul><ul><li>Familiarity with ITP, RFI, NCR, punch-list, mechanical completion, turnover, and quality-record processes.</li></ul><ul><li>Working knowledge of applicable IEC, IEEE, NFPA, ISO, and project-specific standards and requirements.</li></ul><ul><li>Competence in reporting, progress monitoring, work-front planning, and use of standard office applications.</li></ul><br><p><b>Level / Diploma</b></p><br><br><ul><li>Bachelor’s Degree in Electrical Engineering preferred.</li></ul><ul><li>A recognized technical diploma in Electrical Engineering may be accepted with substantial relevant site experience.</li></ul><ul><li>Relevant electrical safety, HV authorization, commissioning, or construction supervision training is an advantage.</li></ul><br><p><b>Languages</b></p><br><br><ul><li>Proficiency in English is mandatory. Knowledge of Arabic is an advantage.</li></ul><br><p><b>Soft Skills</b></p><br><br><ul><li>Strong field presence, leadership, and contractor-management capability.</li></ul><ul><li>Clear communication and coordination skills in a multicultural environment.</li></ul><ul><li>Proactive, practical, safety-conscious, and quality-focused approach.</li></ul><ul><li>Ability to prioritize work, resolve site issues, manage interfaces, and work under schedule pressure.</li></ul><ul><li>Ability to challenge non-compliant work and intervene firmly when safety or quality is at risk.</li></ul><br><p><span>Interested and suitable candidates please apply for the role. Suitable candidates will be contacted directly.</span></p><br><br><br><br><br> </div>

<p>Wood is recruiting for an Electrical &amp; Instrument Supervisor ((Iraqi National) to join its Iraq business unit focusing on receiving and verifying all electrical equipment, ensuring conformity to project specifications and standards. This role is a full-time on-site role in Basra, Iraq with travel requirement.</p><p>Wood forms the Energy &amp; Materials pillar of Sidara - a global partnership uniting leading multidisciplinary engineering, design, and project management companies. www.woodgroup.com</p><p>Diversity Statement We are an equal opportunity employer that recognises the value of a diverse workforce. All suitably qualified applicants will receive consideration for employment on the basis of objective criteria and without regard to the following (which is a non-exhaustive list): race, colour, age, religion, gender, national origin, disability, sexual orientation, gender identity, protected veteran status, or other characteristics in accordance with the relevant governing laws.</p><p>What makes you remarkable? At Wood, we are committed to equal opportunities and welcome all talented individuals to consider joining our team. So even if you don't match every statement below but feel you have some of the experience, knowledge or skills needed for this role, we encourage you to apply. It will take all of us working together to deliver solutions to the world s most critical challenges.</p><p>Expected: Bachelor s degree in electrical engineering, 5 to 10 years of experience in the oil industry, with significant experience with SIMOPS works, Strong understanding of Oil &amp; Gas International Codes and Standards, Proactive and team-oriented approach with the ability to work collaboratively across complex project teams. Strong technical and problem-solving skills, Excellent communication and interpersonal skills, Ability to work effectively under pressure, Detail-oriented with strong organizational skills.</p><p>Wood is recruiting for an Electrical &amp; Instrument Supervisor ((Iraqi National) to join its Iraq business unit focusing on receiving and verifying all electrical equipment, ensuring conformity to project specifications and standards. This role is a full-time on-site role in Basra, Iraq with travel requirement. #Wood #Iraq #Basra #Electrical &amp; Instrument Supervisor</p><p>The role</p><p>This is an exciting opportunity for an experienced Electrical &amp; Instrument Supervisor to join our Iraq Business Unit.</p><p>Our Clients and Projects</p><p>Designing the future. Transforming the world. This Project aims to take over the existing asset and maximize the production in 2 phases. This is a fast-track project and schedule-oriented Design to enhance the production. The Phase 1 will restore, upgrade, and develop the current plant (CPF1) including: Restoration of initial CPF1 capacity; building a new export pipeline (24 , ~30km); restoration of CPF1 integrity and operability; flaring elimination and released water; development of new flowlines, pads, and electrification network for approximately 30 new wells; debottlenecking of the plant; upgrade of the Safety and Security facilities. Our scope is to provide Engineering, Procurement services and Construction assistance (EPsCa) for the initial development phase of the field in Southern Iraq. The scope of services includes FEED, detailed design, procurement support, and construction and commissioning assistance.</p><p>What we can offer</p><ul><li>Meaningful and interesting projects Delivered to high profile clients and complex projects in Iraq</li><li>Commitment to Diversity and Inclusion ; we are an organisation actively committed to diversity and inclusion across our business with employee networks committed to giving all employees a voice</li><li>Competitive salary with regular salary reviews to ensure we are rewarding at the right level in line with the market</li><li>Medical Insurance: Ensures inpatient and outpatient medical care is available should you require treatment.</li><li>Commitment to continued professional development; development plans that are tailored to your individual needs and interests</li><li>Global connections : join experts around the world who are at the leading edge of our industry, shaping the standards of our profession</li><li>Long Service Award: Wood values the commitment and loyalty of our people. Celebrating Long Service provides an opportunity for the business to demonstrate their appreciation of the hard work, dedication and many years services of our employees at 5-year service milestones</li></ul><p>Job Objectives:</p><ul><li>Receive and verify all electrical equipment, ensuring conformity to project specifications and standards.</li><li>Coordinate and schedule equipment deliveries to the site, planning and managing logistics for all electrical equipment.</li><li>Develop and implement preservation plans for electrical equipment on-site, ensuring proper maintenance until installation.</li><li>Supervise the installation of all electrical equipment.</li><li>Coordinate with other disciplines to ensure site readiness, including foundation preparation and electrical interfaces.</li><li>Be proactive in addressing potential issues and ensuring smooth installation processes.</li><li>Implement and oversee QA/QC procedures during equipment installation, conducting inspections to ensure compliance with quality standards.</li><li>Manage and coordinate electrical construction activities, resolving any on-site technical issues.</li><li>Assist in pre-commissioning and commissioning of electrical systems, ensuring all systems meet performance criteria.</li><li>Prepare and manage the hand-over of electrical systems, ensuring all documentation is complete and accurate.</li><li>Interface between interdisciplinary departments and within international teams, ensuring seamless integration of electrical systems</li><li>Maintain and update technical documentation, including technical reports and specifications.</li><li>Troubleshoot and resolve electrical issues, providing technical support as needed.</li><li>Monitor a team of contractor s electrical technicians, providing guidance and training as necessary.</li><li>Monitor and control project costs related to electrical work, identifying, and implementing cost-saving measures.</li><li>Develop and manage electrical work schedules, ensuring timely completion of all electrical activities.</li><li>Assist in the procurement of electrical equipment and materials, reviewing vendor documentation for compliance.</li><li>Identify and mitigate risks related to electrical activities, implementing contingency plans as necessary.</li><li>Manage changes to electrical systems and documentation, evaluating and approving change requests.</li></ul><p><strong>Desired Candidate Profile</strong></p><p>Bachelor s degree in electrical engineering, 5 to 10 years of experience in the oil industry, with significant experience with SIMOPS works, Strong understanding of Oil &amp; Gas International Codes and Standards, Proactive and team-oriented approach with the ability to work collaboratively across complex project teams. Strong technical and problem-solving skills, Excellent communication and interpersonal skills, Ability to work effectively under pressure, Detail-oriented with strong organizational skills.</p>